Shop parts
C3100Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C3100: scanner carriage error

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C3100 is a carriage error. The scanner carriage under the glass did not return to its home position as expected at power-on or after a scan. The usual first suspect is a carriage that moves stiffly. Restart once, then ask a technician to check how freely the carriage moves.

What does C3100 mean?

The scanner carriage carries the CIS that reads originals on the glass, and a home position sensor tells the printer where the carriage is parked. C3100 appears when that sensor does not switch the way the printer expects, either at switch-on or at the end of scanning an original. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C3100?

  • Carriage moves stiffly

    Something on the scanner drive belt, or a dry ISU shaft, makes the carriage hard to move.

  • Wrong drive belt tension

    A belt that is too slack or too tight puts a load on the carriage.

  • Loose connector, FFC or damaged wire

    The links from the home position sensor and the scanner motor to the main/engine PWB (YC31), or the CIS flat cable to the main/engine PWB (YC506), are not making good contact.

  • Home position sensor fault

    The sensor is badly fitted or has failed.

  • Scanner motor fault

    The motor that drives the carriage is badly fitted or has failed.

  • Faulty CIS

    The CIS on the scanner carriage has failed.

  • Old engine firmware

    The engine firmware is faulty and needs the latest version.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Restart once

    Switch the printer off at the power switch, wait a few seconds and switch it on again. Note the code shown.

  2. 2

    If the code returns

    Leave the printer off and call a technician. The remaining checks are inside the machine.

Safety: The manual says to pull the power plug out of the wall socket before taking any cover off. After the work, check that every connector, wire and screw that was removed has gone back in place.

Steps for a technician

  1. 1

    Check carriage movement

    Push the scanner carriage by hand. If it feels heavy, look for foreign matter on the scanner drive belt, clean the belt and grease the ISU shaft.

  2. 2

    Check belt tension

    Set the scanner drive belt to the correct tension.

  3. 3

    Check the connections

    Refit these links: home position sensor to main/engine PWB (YC31), scanner motor to main/engine PWB (YC31) and CIS to main/engine PWB (YC506). Fit a new wire if there is no continuity, and a new FFC if its contacts are peeled, bent or broken.

  4. 4

    Check the home position sensor

    Refit the sensor and its connector. Replace the sensor if the code stays.

  5. 5

    Check the scanner motor

    Refit the motor and its connector. Replace the motor if the code stays.

  6. 6

    Replace the scanner carriage

    Fit a new scanner carriage, then run U411 [Table(ChartA)] and [DP FU(ChartA)].

  7. 7

    Update the firmware

    Upgrade the engine firmware to the newest version.

  8. 8

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the scanner carriage, scanner motor or home position sensor named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if C3100 shows again after one restart. Every check needs the scanner section opened or the boards and firmware worked on.

Questions people ask

What does error C3100 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C3100 is a scanner carriage error. The home position sensor did not report the carriage where the printer expected it at switch-on or after a scan.
How do I fix Kyocera C3100?
Restart the printer once. If C3100 returns, a technician checks whether the carriage moves freely, sets the drive belt tension, checks the wiring and then the sensor, motor and carriage in turn.
Can I still print when a Kyocera M2040dn shows C3100?
The service manual says the machine stops working when it detects a self-diagnostic error like C3100, so plan for a technician visit.
Do I need to run U411 after fixing C3100?
Yes, if the scanner carriage is replaced. The Kyocera manual asks for U411 [Table(ChartA)] and [DP FU(ChartA)] after a new carriage.

Related codes

See all Kyocera ECOSYS M2040dn error codes