Shop parts
C3200Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C3200, C3300 or C3500: CIS scanner error

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: C3200, C3300, C3500

Quick answer

Kyocera ECOSYS M2040dn errors C3200, C3300 and C3500 mean the CIS, the scanning sensor under the glass, gave a bad white reading or lost contact with the scanner chip. The first suspect is the flat cable from the CIS to the main/engine PWB. Restart once, then call a technician to reseat that cable.

What does C3200 mean?

C3200 appears when the white reading taken with the CIS lamp on at start-up is too low. C3300 appears when the correct white reference cannot be obtained during the automatic gain (AGC) process, and C3500 appears when the scanner ASIC and the engine CPU cannot talk to each other. All three use the same three checks in the manual, so they share this page. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C3200?

  • Loose or damaged flat cable

    The FFC from the CIS to the main/engine PWB (YC506) is not seated, or its contacts are damaged.

  • Faulty CIS or scanner carriage

    The CIS fails, so the scanner carriage that holds it is replaced.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Restart once

    Switch the printer off at the power switch, wait a few seconds and switch it on again. Note the code shown.

  2. 2

    If the code returns

    Leave the printer off and call a technician. The remaining checks are inside the machine.

Safety: The manual says to pull the power plug out of the wall socket before taking any cover off. After the work, check that every connector, wire and screw that was removed has gone back in place.

Steps for a technician

  1. 1

    Check the CIS cable

    Reseat the FFC between the CIS and the main/engine PWB (YC506). Fit a new FFC if its contacts are peeled, bent or broken.

  2. 2

    Replace the scanner carriage

    Fit a new scanner carriage, then run U411 [Table(ChartA)] and [DP FU(ChartA)].

  3. 3

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the scanner carriage, CIS or its flat cable named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the code shows again after one restart. The checks need the scanner opened and the main/engine PWB reached.

Questions people ask

What does C3200 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C3200 is a CIS lamp error. The white reading taken by the scanner sensor at start-up was lower than it should be.
What is the difference between Kyocera C3200, C3300 and C3500?
C3200 is a low white reading at start-up, C3300 is a failed white reference during the gain adjustment, and C3500 is a lost link between the scanner chip and the engine CPU. The service manual checks all three the same way.
How do I fix Kyocera C3300?
A technician reseats the CIS flat cable at YC506 on the main/engine PWB. If the code stays, the scanner carriage is replaced and U411 is run, and the main/engine PWB is the last step.
Is C3500 on a Kyocera M2040dn a board fault?
Not always. The Kyocera manual checks the CIS flat cable first, then the scanner carriage, and only then the main/engine PWB.

Related codes

See all Kyocera ECOSYS M2040dn error codes