Kyocera ECOSYS M2040dn error codes and problems
141 pages. Pick the code on your panel or the problem you see. Each page gives the cause, what to check and the part that fixes it.
Service codes (C codes)
The machine stops and asks for service.
- C0100: backup memory device error
- C0120: MAC address data error
- C0130: backup memory reading/writing error
- C0140: backup memory data error
- C0150: engine EEPROM data error
- C0160: engine EEPROM data error
- C0180 and C0170: serial number and counter mismatch
- C0190: backup memory device error (engine)
- C0500, C0510, C0530, C0540 and C0800: engine control errors
- C0840: RTC error (Time for maintenance T)
- C0970: power interruption detection
- C1810 and C1820: paper feeder communication error
- C2000 and C2010: main motor error
- C2600 and C2610: PF feed motor error
- C3100: scanner carriage error
- C3200, C3300 or C3500: CIS scanner error
- C3210 or C3310: DPCIS scanner error
- C4000 or C4010: polygon motor error
- C4201: laser error
- C6000: broken fuser heater
- C6020: thermopile high temperature
- C6030: broken thermopile
- C6050: thermopile low temperature
- C6200: fuser edge thermistor error
- C6220, C6230 or C6250: fuser edge thermistor
- C6400: zero-cross signal error
- C6600: fuser rotation error
- C6610: fuser press-release sensor error
- C6650: thermopile EEPROM error
- C7220: broken in-machine thermistor
- C7800: outer thermistor broken
- C7990: waste toner full
Paper jam codes (J codes)
The code tells you where the paper stopped.
- J0000: power on jam
- J0101, J0104, J0105, J0106: jam caused by software
- J0107: fuser temperature stabilization time-out
- J0110: right cover open detected during printing
- J0501: no paper feed from cassette 1
- J0502, J0503: no feed from cassette 2 or 3 (paper feeder)
- J0508: no paper feed from the duplex section
- J0509: no paper feed from the MP tray
- J0511, J0512, J0513: multi feed jam from a cassette
- J0518: multi-feeding from the duplex section
- J0519: multi-feeding from the MP tray
- J1403: PF feed sensor non-arrival jam (paper feeder 2)
- J1413: PF feed sensor stay jam (paper feeder 2)
- J4002, J4003: registration sensor non-arrival jam from cassette 2 or 3
- J4008: registration sensor non-arrival jam from duplex
- J4012, J4013, J4018: registration sensor stay jam
- J4201, J4202, J4203, J4208, J4209: paper did not reach the exit sensor (fuser jam)
- J4211, J4212, J4213, J4218, J4219: exit sensor stay jam
- J9000: no original feed from the document processor
- J9002: document processor sensor on at start
- J9009: document processor jam during image scanning
- J9010: document processor open during feeding
- J9061: DP feed motor rotation error
- J9110: DP feed sensor multi-feeding jam
- J9300, J9310: DP backside timing sensor jam
- J9400, J9410: DP timing sensor jam
Print, copy and scan problems
No code on the panel, but something is wrong.
- Black dots or spots on copies and prints
- Prints or copies a completely black page
- Blank page: Prints or copies a blank white page
- Blurred print: Blurred image or blurred text
- Dirty back of page: Toner on the back of the page or paper edges
- Driver stuck Deleting: Printer driver stuck on Deleting
- Feeds from MP tray: Feeds from the MP tray instead of the cassette
- Prints garbled characters
- Ghost image or offset image on prints
- Grey background: Grey or dirty background on copies and prints
- Horizontal streaks: Horizontal lines or bands across the page
- Image off-centre: Image shifted or off-centre on the page
- Stopped printing after its IP address changed
- Light print: Light or faded print and copies
- Moire pattern: Moire or wavy pattern on copies
- MP tray not feeding: Does not feed paper from the MP tray
- Network cable problem: Not printing: network cable not connected properly
- Network print fails: Cannot print over the network
- No print in sleep mode: Does not print from sleep mode
- Not connected or Preparing: Kyocera ECOSYS M2040dn: PC shows Not connected or printer stuck on Preparing
- Kyocera ECOSYS M2040dn: only one PC cannot print
- Paper creases: Paper comes out creased or wrinkled
- Paper direction wrong: Prints in the wrong paper direction
- Paper jam: first checks before you look at the code
- Paper loading message: Asks to load paper when paper is loaded
- Shows Paper Mismatch Error
- Part of image missing: Part of the image missing or white patches
- PC does not see printer: Is not recognised by the PC
- Kyocera ECOSYS M2040dn: PC unstable when printing
- Print partly missing: Prints with part of the image missing
- Printer offline: Shows Offline and will not print
- Printer Pending, locked: Shows Printer Pending and locks up
- Kyocera ECOSYS M2040dn: Print Job Error and Printer Unavailable on the PC
- Router or hub problem: Not printing: router or hub not working
- Same page prints endlessly: Keeps printing the same page endlessly
- Scan sent before all pages: Sends a scan from the glass before you add more pages
- Skewed image: Skewed or crooked image
- Stops after a few pages: Stops and locks after printing a few pages
- Toner rubs off the page (fusing failure)
- Uneven density: Uneven print: one part darker or lighter
- Vertical black streaks: Vertical black lines on copies or prints
- Vertical white streaks: Vertical white lines on copies or prints
- Wrong IP or host name: Not printing: router setting, IP or host name wrong
- Kyocera ECOSYS M2040dn: wrong printer driver selected
- Wrong printer port: Kyocera ECOSYS M2040dn: network printer port not set up
Scan and send error codes
Scan to folder, e-mail or FTP fails with a number.
- Scan to e-mail error 1101: mail server not found
- Scan to FTP error 1101: FTP server not found
- Scan to SMB error 1101: destination PC not found
- Scan to e-mail error 1102: mail login failed
- Scan to FTP error 1102: FTP login failed
- Scan to SMB error 1102: login to PC failed
- Scan to SMB error 1103: invalid host, folder or file name
- Scan to e-mail error 1104, 1105, 1106
- Scan to FTP error 1105: FTP not enabled
- Scan to SMB error 1105: SMB not enabled
- Scan to FTP error 1131 and 1132: TLS failed
- Scan to e-mail error 2101: cannot connect to server
- Scan to FTP error 2101: cannot connect to FTP
- Scan to SMB error 2101: cannot connect to PC
- Scan to e-mail error 2102 and 2103: server timeout
- Scan to FTP error 2102 and 2103: FTP timeout
- Scan to e-mail error 2201, 2202, 2204
- Scan to FTP error 2201: FTP communication failed
- Scan to SMB error 2201: writing scan failed
- Scan to FTP error 2202, 2203, 2231
- Scan to SMB error 2203: no reply from PC
- Scan to e-mail error 3101: server returned an error
- Scan to FTP error 3101: FTP server error
- Scan to e-mail error 3201: SMTP authentication
- Scan to e-mail error 4803: SSL session failed
System codes (F codes)
Shown at power on or when the system halts.
- F000: panel and main board cannot talk
- F010 and F020: program or RAM error
- F040: controller and engine not talking
- F050: engine program will not start
- F12X / F33X: scanner control fault
- F15X / F38X: card reader fault
- F18X / F35X: video or print control fault
- F1DX, F26X, F3AX, F47X: controller fault
- F21X to F24X: image processing fault
- F25X, F2BX to F32X: network control fault
- F34X: operation panel process fault
- F46X: printer rendering fault
- F4FX, F51X to F6CX: job or service fault