Kyocera ECOSYS M2040dn errors C2600 and C2610: PF feed motor error
Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw
Codes covered on this page: C2600, C2610
Quick answer
Kyocera ECOSYS M2040dn errors C2600 and C2610 are PF feed motor errors: the motor in the optional paper feeder did not send its ready signal within 2 seconds of starting. C2600 is feeder 1 and C2610 is feeder 2. The manual first checks the motor wiring through the feeder, then the drive gears.
What does C2600 mean?
Each optional paper feeder has its own PF feed motor. C2600 (paper feeder 1) or C2610 (paper feeder 2) appears when that motor's ready signal is still off 2 seconds after start-up. The checks are the same for both; C2610 simply has a longer wiring path through feeder 1. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.
What causes C2600?
Loose connector or damaged wire
The leads from the PF feed motor to the PF main PWB (YC4), from the PF main PWB (YC5) to the drawer connector, and from the drawer connector to the main/engine PWB (YC17) are not making good contact. For C2610 the path also runs through the PF main PWB of feeder 1.
Drive parts not turning smoothly
The coupling or gears in the PF feed motor drive section are stiff or broken.
Faulty PF feed motor
The feeder motor itself has failed.
Faulty main/engine PWB
The main control board is at fault. The manual lists this last.
What can you check yourself?
- 1
Switch off and on
Turn the printer off, remove the plug, wait at least 5 seconds, then plug in and switch on again.
- 2
If the code returns
Leave the printer off and call a technician. The motor and gears are inside the feeder.
Steps for a technician
- 1
Check the connections
Clean the contacts and refit the connectors: PF feed motor to PF main PWB (YC4), PF main PWB (YC5) to drawer connector, and drawer connector to main/engine PWB (YC17). For C2610, check the feeder 2 PF main PWB, then the drawer connector to the feeder 1 PF main PWB (YC6) and on to the main unit. Fit a new wire if there is no continuity.
- 2
Check the drive parts
If the coupling and gears in the PF feed motor drive section do not turn smoothly, clean the gears and grease them. Replace a broken coupling or gear.
- 3
Replace the PF feed motor
If the code stays, fit a new PF feed motor.
- 4
Replace the main/engine PWB
As the final step, fit a new main/engine PWB.
Need a part for this?
The store does not list the PF feed motor or its drive gears for this code, so please ask on WhatsApp for availability.
Ask on WhatsApp: +91 88899-15080When should you call a technician?
Call a technician if C2600 or C2610 comes back after a power reset. The checks involve the feeder wiring, gears and motor.
Questions people ask
- What does error C2600 mean on a Kyocera M2040dn?
- On a Kyocera ECOSYS M2040dn, C2600 is a PF feed motor error for paper feeder 1. The feeder motor did not send its ready signal within 2 seconds of starting.
- What is the difference between Kyocera C2600 and C2610?
- C2600 is the feed motor in paper feeder 1, directly under the printer. C2610 is the feed motor in paper feeder 2, below feeder 1.
- How do I fix Kyocera C2600?
- Switch off and on once. If C2600 returns, a technician checks the feeder motor wiring, cleans and greases the drive gears, and replaces the PF feed motor if needed.
Related codes
- C1810: Paper feeder communication error (PF1)
- C1820: Paper feeder communication error (PF2)
- C2000: Main motor steady state error