Shop parts
C3210Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C3210 or C3310: DPCIS scanner error

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: C3210, C3310

Quick answer

Kyocera ECOSYS M2040dn errors C3210 and C3310 mean the DPCIS, the sensor in the document processor that scans the back of each page, gave a bad white reading. The first suspect is its flat cable to the main/engine PWB. Restart the printer once, then call a technician to reseat that cable.

What does C3210 mean?

The DPCIS reads the second side of originals as they pass through the document processor. C3210 appears when its white reading with the lamp on at start-up is too low, and C3310 appears when a proper white reference is not obtained after the automatic gain (AGC) process. The manual uses the same checks for both. Only the 40 ppm models (M2040dn, M2540dn, M2540dw and M2640idw) have a DPCIS, so the 35 ppm models do not show these codes.

What causes C3210?

  • Loose or damaged flat cable

    The FFC from the DPCIS to the main/engine PWB (YC509) is not seated, or its contacts are damaged.

  • Faulty DPCIS

    The DPCIS sensor itself has failed.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Restart once

    Switch the printer off at the power switch, wait a few seconds and switch it on again. Note the code shown.

  2. 2

    If the code returns

    Leave the printer off and call a technician. The remaining checks are inside the machine.

Safety: The manual says to pull the power plug out of the wall socket before taking any cover off. After the work, check that every connector, wire and screw that was removed has gone back in place.

Steps for a technician

  1. 1

    Check the DPCIS cable

    Reseat the FFC between the DPCIS and the main/engine PWB (YC509). Fit a new FFC if its contacts are peeled, bent or broken.

  2. 2

    Replace the DPCIS

    Fit a new DPCIS, then run U411 [DP FD(ChartA)].

  3. 3

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the DPCIS or its flat cable named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the code shows again after one restart. The checks need the document processor and the main/engine PWB opened up.

Questions people ask

What does C3210 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C3210 is a DPCIS lamp error. The back-side scanner in the document processor gave a white reading lower than expected at start-up.
What is the difference between Kyocera C3210 and C3310?
C3210 is a low white reading at start-up, while C3310 means the white reference was not obtained after the gain adjustment. The service manual checks both the same way.
Why does my Kyocera M2135dn never show C3210?
Only the 40 ppm models (M2040dn, M2540dn, M2540dw and M2640idw) have the DPCIS back-side scanner, so these codes do not apply to the 35 ppm models.
What adjustment is needed after replacing the DPCIS?
The Kyocera manual asks for U411 [DP FD(ChartA)] after fitting a new DPCIS.

Related codes

See all Kyocera ECOSYS M2040dn error codes