Shop parts
C4000Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C4000 or C4010: polygon motor error

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: C4000, C4010

Quick answer

Kyocera ECOSYS M2040dn errors C4000 and C4010 mean the polygon motor inside the laser scanner unit (LSU) did not reach, or did not hold, its ready state. The first suspect is the LSU connector on the main/engine PWB. Restart the printer once, then call a technician to check the LSU.

What does C4000 mean?

The polygon motor spins a mirror inside the LSU and sends a ready signal once it runs steadily. C4000 appears when that ready signal has not come on 10 seconds after the motor starts. C4010 appears when the signal drops out for 1 second in a row after the motor has settled. The manual checks both the same way. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C4000?

  • Loose connector or damaged wire

    The lead from the LSU (polygon motor) to the main/engine PWB (YC3) is not making good contact.

  • Polygon motor not turning properly

    The LSU is badly fitted or the polygon motor in it has failed.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Restart once

    Switch the printer off at the power switch, wait a few seconds and switch it on again. Note the code shown.

  2. 2

    If the code returns

    Leave the printer off and call a technician. The remaining checks are inside the machine.

Safety: The LSU is a laser unit. The manual warns never to take the optical unit apart, because escaping laser light can harm the eyes. Unplug the machine before removing covers, and guard against static when handling the LSU.

Steps for a technician

  1. 1

    Check the connection

    Clean the contacts and refit the connector between the LSU (polygon motor) and the main/engine PWB (YC3). Fit a new wire if there is no continuity.

  2. 2

    Check the LSU

    Listen to the polygon motor as it runs. If it does not sound right, refit the LSU, and replace it if the code stays.

  3. 3

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the LSU (laser scanner unit) named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if C4000 or C4010 shows again after one restart. The checks need the LSU reached inside the machine.

Questions people ask

What does C4000 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C4000 is a polygon motor startup error. The motor in the laser unit did not report ready within 10 seconds of starting.
What is the difference between Kyocera C4000 and C4010?
C4000 means the polygon motor never reported ready at start-up. C4010 means it reported ready and then lost that signal for 1 second while running.
How do I fix Kyocera C4010?
A technician checks the LSU connector at YC3 on the main/engine PWB, listens to the polygon motor, refits or replaces the LSU, and replaces the main/engine PWB only as the last step.
Can I open the laser unit to fix C4000 myself?
No. The Kyocera service manual warns never to take the laser optical unit apart, because escaping laser light can damage the eyes.

Related codes

See all Kyocera ECOSYS M2040dn error codes