Shop parts
C4201Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C4201: laser error

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C4201 is a laser error. The printer switched the laser on but did not detect the beam within 1 second. The first suspect is the flat cable from the LSU's APC PWB to the main/engine PWB. Restart once, then call a technician, because the laser unit must not be opened.

What does C4201 mean?

The laser scanner unit (LSU) writes the image onto the drum. After the laser starts firing, the printer expects to sense the beam. C4201 appears when it is not sensed for 1 second after emission starts, which the manual links to the cable, the laser diode or the main board. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C4201?

  • Loose or damaged flat cable

    The FFC from the LSU (APC PWB) to the main/engine PWB (YC505) is not seated, or its contacts are damaged.

  • Faulty laser diode

    The laser diode in the LSU has failed, so the LSU is refitted or replaced.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Restart once

    Switch the printer off at the power switch, wait a few seconds and switch it on again. Note the code shown.

  2. 2

    If the code returns

    Leave the printer off and call a technician. The remaining checks are inside the machine.

Safety: The LSU is a laser unit. The manual warns never to take the optical unit apart, because escaping laser light can harm the eyes. Unplug the machine before removing covers, and guard against static when handling the LSU.

Steps for a technician

  1. 1

    Check the LSU cable

    Reseat the FFC between the LSU (APC PWB) and the main/engine PWB (YC505). Fit a new FFC if its contacts are peeled, bent or broken.

  2. 2

    Check the LSU

    Refit the LSU while guarding against static electricity. Replace the LSU if the code stays.

  3. 3

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the LSU (laser scanner unit) named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if C4201 shows again after one restart. Every check involves the laser unit or the main/engine PWB.

Questions people ask

What does error C4201 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C4201 is a laser error. The laser was switched on but was not detected within 1 second.
How do I fix Kyocera C4201?
A technician first reseats the LSU flat cable at YC505 on the main/engine PWB. If the code stays, the LSU is refitted with care against static and then replaced, with the main/engine PWB last.
Does Kyocera C4201 always mean a new laser unit?
No. The Kyocera service manual checks the flat cable first and refits the LSU before replacing it.
Is it safe to open the LSU to look at the laser?
No. The service manual warns never to take the laser optical unit apart, because escaping laser light can damage the eyes.

Related codes

See all Kyocera ECOSYS M2040dn error codes