Shop parts
C7990Service codeWarning

Kyocera ECOSYS M2040dn error C7990: waste toner full

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C7990 means the waste toner sensor reports that the waste toner store inside the drum unit is full. This model keeps waste toner in the drum unit, not in a separate box. First switch the printer off and on again. If the code stays, the drum unit needs replacing.

What does C7990 mean?

Used toner cleaned off the drum collects in a reservoir inside the drum unit, and a sensor watches how full it is. When that sensor says the reservoir is full, the printer stops and shows C7990. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C7990?

  • Drum unit waste toner store is full

    The reservoir inside the drum unit has filled up. The manual asks for a restart first and a new drum unit only if the code stays.

  • Loose connector or damaged wire

    The lead from the waste toner sensor to the main/engine PWB (YC2) is not making good contact.

  • Faulty waste toner sensor

    The sensor itself reports full when it should not.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Restart the printer

    Switch the printer off, wait a few seconds and switch it on again. The manual tries this before replacing the drum unit.

  2. 2

    Plan for a drum unit

    If C7990 is still on screen after the restart, the waste toner store in the drum unit is full and the drum unit has to be replaced.

Steps for a technician

  1. 1

    Restart, then replace the drum unit

    Cycle the power. If the code does not clear, fit a new drum unit, since the full waste toner store is part of it. The drum unit is part of the MK-1150, MK-1151, MK-1152 and MK-1154 maintenance kits; after fitting a full kit, the manual asks for U251 (maintenance counter clear) and U130 when a new developer unit is fitted.

  2. 2

    Check the connection

    Clean the contacts and refit the connector between the waste toner sensor and the main/engine PWB (YC2). If a wire has no continuity, fit a new wire.

  3. 3

    Replace the waste toner sensor

    If the code remains with a new drum unit and good wiring, fit a new waste toner sensor.

  4. 4

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the complete drum unit or the waste toner sensor named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if C7990 stays after a restart and a new drum unit. The next checks are the sensor wiring, the sensor and the main board.

Questions people ask

What does error C7990 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C7990 means waste toner full. The sensor reports that the waste toner store inside the drum unit is full.
How do I clear Kyocera C7990?
Switch the printer off and on once. If C7990 is still shown, the Kyocera service manual says to replace the drum unit, because the waste toner store is built into it.
Where is the waste toner box on a Kyocera M2040dn?
The Kyocera ECOSYS M2040dn keeps its waste toner in a reservoir inside the drum unit. That is why a full reservoir is fixed by replacing the drum unit.
Kyocera C7990 still showing after a new drum unit?
Then a technician checks the waste toner sensor wiring to the main/engine PWB (YC2), then the sensor itself, and finally the main/engine PWB.

See all Kyocera ECOSYS M2040dn error codes