Shop parts
ProblemWarning

Kyocera ECOSYS M2040dn prints or copies a completely black page

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

A fully black page from a Kyocera ECOSYS M2040dn means the whole sheet was treated as image. Print the Test Page from Service Setting. If only copies are black, the scanner is the cause. If the test page is black, the first check is that the main charger unit and drum unit are properly fitted and grounded.

What is happening?

On the scanner side, Kyocera lists a solid white or black copy under one heading, with the same checks for both: the original, slit glass, scan position, home position sensor, drive belt, drive gear and CIS. On the engine side, an all black print points to the charge on the drum: the main charger and drum unit seating, their contacts, the developer bias contact, the LSU and high voltage cables, and the boards. The same checks apply to all eight models in this service manual.

What causes it?

  • Scanner not reading correctly

    The original is upside down, the slit glass is loose, the DP scan position (U068) is off, or the home position sensor, CIS cable, scanner drive belt or drive gear is loose.

  • Faulty CIS, DPCIS or main board

    The image sensor or the main/engine PWB behind it.

  • Drum or main charger not seated (engine)

    The main charger unit or drum unit is not fitted properly and is not grounded.

  • Contacts (engine)

    The main charger contact or the developer bias contact is dirty or bent.

  • Cables, boards and LSU (engine)

    The LSU (APC PWB) cable (YC505), the high voltage PWB cable (YC16), the high voltage PWB, a dirty or faulty LSU, or the main/engine PWB.

What can you check yourself?

  1. 1

    Print the test page

    Go to System Menu > Adjustment/Maintenance > Service Setting and print the Test Page (a grey halftone sheet). If the fault is on the test page, the printing engine is the cause. If the test page is clean and only copies or scans show it, the scanner is the cause.

  2. 2

    Check the original

    If only copies are black, check the original is loaded the right way round and try again.

Safety: The manual says to pull the power plug before taking anything apart, to handle the charger sections with care because they carry high voltage, and never to open the laser optical unit (LSU) because the laser can harm eyesight. Users should stay with settings, paper, toner and glass cleaning.

Steps for a technician

  1. 1

    Isolate scanner or engine

    Print the Test Page from Service Setting. A fault on the test page is an engine factor; a clean test page means a scanner factor. A fault that scales with zoom copying is also a scanner factor. On the scanner side, check whether it follows the contact glass, the DP front side (main unit CIS) or the DP back side (DPCIS, 40 ppm models only).

  2. 2

    Scanner side

    Correct the original direction. Refit the slit glass, adjust U068 [DP Read], refit the home position sensor, reseat the CIS FFC (YC506), and refit the scanner drive belt and drive gear.

  3. 3

    Scanner hardware

    Replace the scanner carriage and run U411 Table(ChartA) and DP FU(ChartA), or the DPCIS with U411 [DP FD(ChartA)] for back sides. Then the main/engine PWB.

  4. 4

    Drum and main charger seating (engine)

    Fit the main charger unit onto the drum unit and seat the drum unit in the machine so it is firmly grounded.

  5. 5

    Contacts

    Clean and reshape the main charger contact and the developer bias contact so both ground securely.

  6. 6

    Cables

    Reseat the LSU (APC PWB) FFC (YC505) and the high voltage PWB cable (YC16). Replace a damaged cable or one without continuity.

  7. 7

    Boards and LSU

    Replace the high voltage PWB, then the LSU, then the main/engine PWB.

Need a part for this?

The store does not list the main charger unit, LSU, high voltage PWB or main/engine PWB named for this fault, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the test page prints solid black. The checks after that need the drum unit, charger and boards handled.

Questions people ask

Why is my Kyocera M2040dn printing black pages?
If the Test Page is solid black, the engine is the cause. The Kyocera service manual first checks that the main charger unit and drum unit are seated and grounded, then the contacts, cables, LSU and boards.
Copies come out black but prints are fine?
Then the scanner is the cause. The manual checks the original direction, slit glass, scan position, home position sensor, drive belt, drive gear and CIS.
Can a loose drum unit cause black pages on a Kyocera?
Yes. The first engine step in the service manual is to refit the main charger unit and drum unit so they are properly grounded.

Related codes

See all Kyocera ECOSYS M2040dn error codes