Shop parts
C0130Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C0130: backup memory reading/writing error

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C0130 means the printer cannot read from or write to its flash memory, where it keeps backup data. The first cause the manual lists is the flash memory not working properly. Start with a full power reset. If C0130 returns, a technician checks the main/engine PWB.

What does C0130 mean?

The printer keeps its backup data in flash memory on the main/engine PWB. C0130 shows when it can no longer read that memory or save to it. The manual has only two checks: a power reset, then the main/engine PWB connectors, wiring and the board itself. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C0130?

  • Flash memory not working properly

    A temporary fault that a full power reset may clear.

  • Main/engine PWB connector, wire or board fault

    A connector on the main/engine PWB is loose, a wire is damaged, or the board has failed.

What can you check yourself?

  1. 1

    Full power reset

    Turn the power switch off and pull out the power cord. Wait at least 5 seconds, plug it back in and switch on.

  2. 2

    If the code returns

    Leave the printer off, note the code shown on the panel and call a technician.

Safety: Only the power reset is a user task. Opening the printer to reach the boards is technician work; switch off and pull the plug before any cover is removed. When a new main/engine PWB is fitted, the manual says to move the EEPROM from the old board to the new one, run U004 if C0180 appears, and check the network settings because the MAC address changes.

Steps for a technician

  1. 1

    Reset the main power

    Switch off, unplug, wait 5 seconds, then reconnect the cord and switch on.

  2. 2

    Check the main/engine PWB

    Refit the main/engine PWB connectors. Repair or replace any wire that is pinched or scratched. If the code stays, fit a new main/engine PWB.

Need a part for this?

The store does not list the main/engine PWB for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if C0130 comes back after a full power reset. The next step is on the main/engine PWB.

Questions people ask

What does error C0130 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C0130 is a backup memory reading/writing error. The printer cannot read or write the flash memory on its main/engine PWB.
How do I fix Kyocera C0130?
Switch off, unplug for at least 5 seconds and switch on again. If C0130 returns, a technician refits the main/engine PWB connectors and replaces the board if needed.
Is Kyocera C0130 the same as C0140?
No. C0130 means the flash memory cannot be read or written at all, while C0140 means the data read at start-up is judged abnormal. C0140 adds a U021 memory initialization step.

Related codes

See all Kyocera ECOSYS M2040dn error codes