Shop parts
C0140Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C0140: backup memory data error

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C0140 means the backup data the printer reads from flash memory at start-up looks abnormal. The manual's first suspect is the flash memory not working properly. Start with a full power reset. If the code returns, a technician runs maintenance mode U021 and then checks the main/engine PWB.

What does C0140 mean?

When the printer powers up, it reads its saved backup data from flash memory. C0140 appears if that data is judged abnormal. The manual tries a power reset, then the U021 memory initialization, then the main/engine PWB. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C0140?

  • Flash memory not working properly

    A temporary fault that a full power reset may clear.

  • Flash memory data needs initializing

    If a reset does not help, the manual initializes the memory with maintenance mode U021.

  • Main/engine PWB connector, wire or board fault

    A connector on the main/engine PWB is loose, a wire is damaged, or the board has failed.

What can you check yourself?

  1. 1

    Full power reset

    Turn the power switch off and pull out the power cord. Wait at least 5 seconds, plug it back in and switch on.

  2. 2

    If the code returns

    Leave the printer off, note the code shown on the panel and call a technician.

Safety: Only the power reset is a user task. Opening the printer to reach the boards is technician work; switch off and pull the plug before any cover is removed. Note that U021 resets user settings to factory defaults, so record important settings first if the printer can still start.

Steps for a technician

  1. 1

    Reset the main power

    Switch off, unplug, wait 5 seconds, then reconnect the cord and switch on.

  2. 2

    Run U021

    Run maintenance mode U021 (initialize memory). Per the maintenance mode section, this returns backup settings to factory defaults by destination, but keeps machine-specific data such as counters, service call history and adjustments.

  3. 3

    Check the main/engine PWB

    Refit the main/engine PWB connectors. Repair or replace any wire that is pinched or scratched. If the code stays, fit a new main/engine PWB.

Need a part for this?

The store does not list the main/engine PWB for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if C0140 comes back after a full power reset. U021 and the main board checks are service tasks.

Questions people ask

What does error C0140 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C0140 is a backup memory data error. The data the printer reads from its flash memory at start-up is judged abnormal.
How do I clear Kyocera C0140?
Switch off, unplug for at least 5 seconds and switch on. If C0140 returns, a technician runs maintenance mode U021 and, if needed, checks or replaces the main/engine PWB.
Will U021 erase my settings?
U021 sets the backup data back to factory defaults for the region, but the manual says counters, service call history and machine adjustments are kept.

Related codes

See all Kyocera ECOSYS M2040dn error codes