Kyocera ECOSYS M2040dn error C0100: backup memory device error
Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw
Quick answer
Kyocera ECOSYS M2040dn error C0100 is a backup memory device error: the printer's flash memory reports an abnormal status. The first cause the manual lists is the EEPROM not working properly. Start with a full power reset: switch off, unplug, wait 5 seconds, plug back in and switch on.
What does C0100 mean?
The printer stores its settings and machine data in memory on the main/engine PWB. C0100 appears when that flash memory sends back an abnormal status. The checks in the manual centre on the EEPROM chip on the main/engine PWB and the board itself. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.
What causes C0100?
EEPROM not working properly
A temporary fault that a full power reset may clear.
EEPROM not seated properly
The EEPROM chip on the main/engine PWB is not fitted correctly.
Faulty EEPROM
The EEPROM chip itself has failed.
Main/engine PWB connector, wire or board fault
A connector on the main/engine PWB is loose, a wire is damaged, or the board has failed.
What can you check yourself?
- 1
Full power reset
Turn the power switch off and pull the power cord out. Wait at least 5 seconds, plug it back in and switch on.
- 2
If the code returns
Leave the printer off and call a technician. The remaining checks are on the main/engine PWB inside the machine.
Steps for a technician
- 1
Reset the main power
Switch off, unplug, wait 5 seconds, then reconnect and switch on.
- 2
Refit the EEPROM
Reseat the EEPROM on the main/engine PWB.
- 3
Replace the EEPROM
Fit a new EEPROM on the main/engine PWB. Code C0180 will then show; run maintenance mode U004 (machine number) to match the serial numbers.
- 4
Check the main/engine PWB
Refit the main/engine PWB connector. Repair or replace any wire that is pinched or scratched. If that does not fix it, fit a new main/engine PWB.
Need a part for this?
The store does not list the EEPROM or the main/engine PWB for this code, so please ask on WhatsApp for availability.
Ask on WhatsApp: +91 88899-15080When should you call a technician?
Call a technician if C0100 comes back after a full power reset. The next steps involve the EEPROM chip and the main/engine PWB.
Questions people ask
- What does error C0100 mean on a Kyocera M2040dn?
- On a Kyocera ECOSYS M2040dn, C0100 is a backup memory device error. The flash memory on the main/engine PWB has reported an abnormal status.
- How do I clear Kyocera C0100?
- Switch the printer off, unplug it, wait at least 5 seconds, then plug in and switch on. If C0100 returns, a technician checks and refits or replaces the EEPROM on the main/engine PWB.
- Why does C0180 appear after fixing Kyocera C0100?
- When the EEPROM on the main/engine PWB is replaced, the Kyocera service manual expects C0180 to appear. The technician then runs maintenance mode U004 to set the machine number.