Shop parts
C0180Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C0180 and C0170: serial number and counter mismatch

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: C0180, C0170

Quick answer

Kyocera ECOSYS M2040dn error C0180 means the machine serial number on the main side and engine side do not match at power-on. C0170 is a similar mismatch in the counters. The usual cause is a main/engine PWB or EEPROM taken from another machine. A technician compares both numbers in maintenance mode U004.

What does C0180 mean?

The printer stores its serial number, and its counters, on both the main side and the engine side. C0180 shows when the two serial numbers differ at power-on, which the manual also expects right after an EEPROM or board change. C0170 shows when the billing counter, life counter or scanner counter differs between the two sides; the manual gives it the same U004-based checks as C0180. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C0180?

  • Main/engine PWB from another machine

    The main serial number in U004 is different because a board from a different unit was fitted.

  • EEPROM from another machine

    The engine serial number in U004 is different because the EEPROM came from a different unit.

  • Faulty main/engine PWB

    The main serial number is wrong because the board has failed.

  • Faulty or badly seated EEPROM

    The engine serial number is wrong because the chip is loose or has failed.

  • Main/engine PWB fault

    The board is faulty even though the numbers check out. The manual lists this last.

What can you check yourself?

  1. 1

    Think about recent repairs

    C0180 commonly follows a main board or EEPROM change. Tell your technician if one was done recently.

  2. 2

    Switch off and call a technician

    Note the code and leave the printer off. The checks need maintenance mode access.

Safety: Running U004 with Execute writes the serial number, so it should only be done by a technician who has confirmed the numbers. When a new main/engine PWB is fitted, the manual says to move the EEPROM from the old board to the new one, run U004 if C0180 appears, and check the network settings because the MAC address changes.

Steps for a technician

  1. 1

    Compare the main serial number

    Open U004 and compare the main and engine serial numbers. If the main number is the odd one out, fit the correct main/engine PWB for this machine.

  2. 2

    Compare the engine serial number

    If the engine number is the odd one out, fit the correct EEPROM for this machine on the main/engine PWB.

  3. 3

    Replace the main/engine PWB

    If the main number is wrong and the board is faulty, fit a new main/engine PWB and then run U004.

  4. 4

    Refit or replace the EEPROM

    If the engine number is wrong, reseat the EEPROM. If that does not help, fit a new EEPROM and run U004. When you only want to read the numbers, do not choose Execute and press Start in U004; the manual warns this writes a different serial number over the old one.

  5. 5

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the EEPROM or the main/engine PWB for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician whenever C0180 or C0170 appears. Every step needs maintenance mode U004 or work on the main/engine PWB.

Questions people ask

What does error C0180 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C0180 means the machine serial number stored on the main side does not match the one on the engine side when the printer is switched on.
How do I fix Kyocera C0180 after replacing the main board?
The Kyocera service manual says to run maintenance mode U004 to match the serial numbers in the boards, then switch off and on, waiting more than 5 seconds between them.
What is Kyocera error C0170?
C0170 is a charger count error. One of the billing, life or scanner counters does not match between the main side and the engine side, and the manual checks it the same way as C0180.
Is it safe to run U004 on a Kyocera M2040dn?
Only after checking the numbers. The manual warns that choosing Execute and pressing Start in U004 overwrites the serial number.

Related codes

See all Kyocera ECOSYS M2040dn error codes