Kyocera ECOSYS M2040dn error C0150: engine EEPROM data error
Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw
Quick answer
Kyocera ECOSYS M2040dn error C0150 is an engine EEPROM data error: the EEPROM keeps returning values that do not match what was written or read before. The first cause the manual lists is the EEPROM not working properly. Start with a full power reset, then a technician checks the EEPROM on the main/engine PWB.
What does C0150 mean?
The engine EEPROM is a small memory chip on the main/engine PWB. C0150 shows when, 8 times in a row, a value read back after writing does not match what was written, or repeated reads of the same location do not agree. The manual tries a reset, then refits and then replaces the EEPROM, then checks the board. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.
What causes C0150?
EEPROM not working properly
A temporary fault that a full power reset may clear.
EEPROM not seated properly
The EEPROM chip on the main/engine PWB is not fitted correctly.
Faulty EEPROM
The EEPROM chip itself has failed.
Main/engine PWB connector, wire or board fault
A connector on the main/engine PWB is loose, a wire is damaged, or the board has failed.
What can you check yourself?
- 1
Full power reset
Turn the power switch off and pull out the power cord. Wait at least 5 seconds, plug it back in and switch on.
- 2
If the code returns
Leave the printer off, note the code shown on the panel and call a technician.
Steps for a technician
- 1
Reset the main power
Switch off, unplug, wait 5 seconds, then reconnect the cord and switch on.
- 2
Refit the EEPROM
Reseat the EEPROM on the main/engine PWB.
- 3
Replace the EEPROM
Fit a new EEPROM on the main/engine PWB, then run maintenance mode U004 (machine number).
- 4
Check the main/engine PWB
Refit the main/engine PWB connectors. Repair or replace any wire that is pinched or scratched. If the code stays, fit a new main/engine PWB.
Need a part for this?
The store does not list the EEPROM or the main/engine PWB for this code, so please ask on WhatsApp for availability.
Ask on WhatsApp: +91 88899-15080When should you call a technician?
Call a technician if C0150 comes back after a full power reset. The remaining steps are on the EEPROM chip and the main/engine PWB.
Questions people ask
- What does error C0150 mean on a Kyocera M2040dn?
- On a Kyocera ECOSYS M2040dn, C0150 is an engine EEPROM data error. The EEPROM on the main/engine PWB gave mismatched data 8 times in a row.
- How do I fix Kyocera C0150?
- Start with a full power reset. If it returns, a technician refits the EEPROM, replaces it if needed and runs U004, and then checks the main/engine PWB.
- What is the difference between Kyocera C0150 and C0160?
- Both are engine EEPROM data errors. C0150 is about repeated write or read mismatches, while C0160 means the data read is judged abnormal; C0160 adds a U021 step and does not include reseating the chip.