Shop parts
C0500Service codeCritical: machine stops

Kyocera ECOSYS M2040dn errors C0500, C0510, C0530, C0540 and C0800: engine control errors

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: C0500, C0510, C0530, C0540, C0800

Quick answer

On the Kyocera ECOSYS M2040dn, errors C0500, C0510, C0530, C0540 and C0800 are engine control errors. The manual blames the main/engine PWB not working correctly for all five. Start with a full power reset: switch off, unplug for 5 seconds and switch on. If the code returns, a technician checks the main/engine PWB.

What does C0500 mean?

Each code reports something different the firmware noticed: C0500 means the main motor keeps turning when it should be locked, C0510 means the high voltage PWB control signal is on while the drum unit is not being driven, C0530 means the backup task has stopped for 30 seconds or more, C0540 means a solenoid has stayed on too long, and C0800 means the J010x print sequence jam happened twice in a row. The manual gives all five the same two checks: a power reset, then the main/engine PWB, with C0510 also covering the flat cable (FFC). The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C0500?

  • Main/engine PWB not working correctly

    A temporary fault on the main board that a full power reset may clear.

  • Main/engine PWB connector, wire or board fault

    A connector on the main/engine PWB is loose, a wire is damaged, or the board has failed. For C0510 the flat cable (FFC) is also checked.

What can you check yourself?

  1. 1

    Full power reset

    Turn the power switch off and pull out the power cord. Wait at least 5 seconds, plug it back in and switch on.

  2. 2

    If the code returns

    Leave the printer off, note the code shown on the panel and call a technician.

Safety: Only the power reset is a user task. Opening the printer to reach the boards is technician work; switch off and pull the plug before any cover is removed. When a new main/engine PWB is fitted, the manual says to move the EEPROM from the old board to the new one, run U004 if C0180 appears, and check the network settings because the MAC address changes.

Steps for a technician

  1. 1

    Reset the main power

    Switch off, unplug, wait 5 seconds, then reconnect the cord and switch on.

  2. 2

    Check the main/engine PWB

    Refit the main/engine PWB connectors (and the FFC for C0510). Repair or replace any wire or FFC that is pinched or scratched. If the code stays, fit a new main/engine PWB.

Need a part for this?

The store does not list the main/engine PWB for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if any of these codes comes back after a full power reset. The only further step is on the main/engine PWB.

Questions people ask

What does error C0500 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C0500 means the engine firmware has detected a drive lock problem, with the main motor running on continuously. The manual's fix is a power reset, then the main/engine PWB.
What does Kyocera C0800 print sequence error mean?
C0800 means the print sequence jam J010x happened twice in a row. The Kyocera service manual treats it as a main/engine PWB issue: power reset first, then board checks.
How do I fix Kyocera C0510 or C0540?
Switch off, unplug for at least 5 seconds and switch on. If the code returns, a technician refits the main/engine PWB connectors and replaces the board if needed.
Is Kyocera C0530 serious?
C0530 means the backup task has not run for 30 seconds or more. Like the other codes on this page, it calls for a power reset and then a main/engine PWB check.

Related codes

See all Kyocera ECOSYS M2040dn error codes