Shop parts
C0840Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C0840: RTC error (Time for maintenance T)

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C0840 is an RTC error, where the printer's real-time clock has gone back in time or holds an invalid date. After a power reset the panel may show "Time for maintenance T". The first fix the manual gives is to set the date and time again in the System Menu.

What does C0840 mean?

The RTC is the printer's built-in clock. At start-up the printer flags C0840 if the clock has gone back in time, if the machine has had no power for 5 years or more, or if the clock is set before 1 January 2000; every 5 minutes it also checks that the clock has not gone back since the last check. Once C0840 is detected and the power is reset, the printer runs partly and shows "Time for maintenance T". The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C0840?

  • Clock not set correctly

    The date and time in the RTC are wrong.

  • Main/engine PWB loosely fitted

    The screws holding the main/engine PWB are not tight.

  • Main/engine PWB connector, wire or board fault

    A connector on the main/engine PWB is loose, a wire is damaged, or the board has failed.

What can you check yourself?

  1. 1

    Set the date and time

    Open the System Menu and set the correct date and time on the printer.

  2. 2

    Switch off and on

    Turn the printer off, wait a few seconds and switch it on. If C0840 or "Time for maintenance T" stays, call a technician.

Safety: Setting the date and time is a user task. Work on the main/engine PWB is for a technician, with the printer switched off and unplugged.

Steps for a technician

  1. 1

    Set the RTC

    Set the date and time in the System Menu.

  2. 2

    Retighten the main/engine PWB

    Tighten the screws that hold the main/engine PWB.

  3. 3

    Check the main/engine PWB

    Refit the main/engine PWB connectors. Repair or replace any wire that is pinched or scratched. If the code stays, fit a new main/engine PWB.

Need a part for this?

The store does not list the main/engine PWB for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if C0840 returns after you set the date and time. The next steps are on the main/engine PWB.

Questions people ask

What does Kyocera C0840 Time for maintenance T mean?
On a Kyocera ECOSYS M2040dn, C0840 is an RTC (clock) error. After a power reset the printer runs partly and shows "Time for maintenance T" until the clock problem is fixed.
How do I fix Kyocera C0840?
Set the correct date and time in the System Menu. If the error comes back, a technician tightens the main/engine PWB screws and checks its connectors and the board.
Why does C0840 appear after a Kyocera printer was stored for a long time?
The manual lists no power for 5 years or more as one of the start-up conditions for C0840, along with a clock that has gone back or is set before 2000.

Related codes

See all Kyocera ECOSYS M2040dn error codes