Shop parts
F4FXSystem codeCritical: machine stops

Kyocera ECOSYS M2040dn error F4FX, F51X to F6CX: job or service fault

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: F4FX, F51X, F52X, F53X, F55X, F56X, F57X, F58X, F59X, F5AX, F5BX, F5CX, F5DX, F5EX, F5FX, F62X, F63X, F69X, F6AX, F6BX, F6CX

Quick answer

Kyocera ECOSYS M2040dn errors F4FX, F51X to F5FX and F62X to F6CX are faults in the controller software that runs jobs and services. They share one fix in the manual, and Kyocera wants a USB log taken right after the error. Start with a full power reset, plug out for a minute.

What does F4FX mean?

These codes come from job management (F4FX), job execution (F51X to F57X), service management and execution (F58X to F5FX, F62X), device control (F63X) and the HyPAS-E part (F69X to F6CX, touch panel models only). The manual notes F5DX, especially F5D9 to F5DD, happens during fax reception or URDS processing, so the data sent from the PC should be checked. For most of these codes, Kyocera needs the USB log saved straight after the error. The same code and checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, since Kyocera covers all of them in one service manual.

What causes F4FX?

  • Data sent from a PC (F5DX)

    F5D9 to F5DD occur during fax reception or URDS processing; check the data sent from the PC.

  • Main backup data

    Stored data may need to be reset with U021.

  • Main/engine PWB fault

    The main board has failed.

What can you check yourself?

  1. 1

    Full power reset

    Switch off at the power switch and pull the plug from the wall. Some power stays in the machine with the switch off, so wait a minute or more, then plug in and switch on.

  2. 2

    Check what was being sent

    If the error came while a fax or a PC job was coming in, note what it was. The manual links F5DX to the data sent from the PC.

  3. 3

    If the code comes back

    Write down the exact code shown, switch the printer off and call a technician. The other checks are inside the machine.

Safety: Before anyone opens the machine to work on boards or cables, switch it off and pull the plug. Part of the machine stays powered while the switch is off, so the plug must come out.

Steps for a technician

  1. 1

    Save the USB log first

    Because Kyocera needs the log from right after the error, save a USB log before other steps where possible.

  2. 2

    Check the DDR memory (DIMM)

    Kyocera's first check for any F code: take the DIMM out of slot YS500 on the main/engine PWB, refit it and test. If the error repeats, replace the DIMM.

  3. 3

    Run U021 (backup initialization)

    Run maintenance mode U021 to reset the controller backup data, then test the machine again.

  4. 4

    Replace the main/engine PWB

    If the error still shows, fit a new main/engine PWB and test again.

  5. 5

    Send the log to Kyocera

    If the error continues, send the USB log to Kyocera service support.

Need a part for this?

The store does not list the main/engine PWB or DIMM named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the F4FX family error does not clear after a power reset with the plug out for a minute or more, or if it keeps coming back.

Questions people ask

What does F4FX mean on a Kyocera printer?
F4FX covers F4F0 to F4FF and is a fault in job management. The manual's fix is U021 and then a new main/engine PWB.
What causes Kyocera F5DX?
The manual says F5DX, especially F5D9 to F5DD, happens during fax reception or URDS processing, and the data sent from the PC should be checked.
Does F69X apply to the M2040dn?
The manual marks F69X to F6CX, the HyPAS-E part, as touch panel models only, so they are not expected on the LCD M2040dn.
Why save a USB log straight away?
For these codes the Kyocera manual says the log from just after the error is needed for analysis.

Related codes

See all Kyocera ECOSYS M2040dn error codes