Shop parts
F34XSystem codeCritical: machine stops

Kyocera ECOSYS M2040dn error F34X: operation panel process fault

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error F34X means the machine found a fault in how it manages the operation panel, such as the panel not answering a command in time. On LCD models like the M2040dn the manual says it is not a hardware fault. Start with a full power reset, plug out for a minute.

What does F34X mean?

F34X covers F340 to F34F. It is raised by the panel management software, for example when a command to the panel times out. On touch panel models a loose panel cable can be the hardware cause, but for LCD models the manual says hardware is not the cause. The step list still starts with the panel cable, then U021 and the boards. The same code and checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, since Kyocera covers all of them in one service manual.

What causes F34X?

  • Panel process fault

    The panel did not respond to a command in time.

  • Panel cable (touch panel models)

    On touch panel models a loose cable between the panel and the main/engine PWB can cause it.

  • Controller backup data

    Stored controller data may need to be reset with U021.

  • Panel board or main/engine PWB fault

    One of the two boards has failed.

What can you check yourself?

  1. 1

    Full power reset

    Switch off at the power switch and pull the plug from the wall. Some power stays in the machine with the switch off, so wait a minute or more, then plug in and switch on.

  2. 2

    If the code comes back

    Write down the exact code shown, switch the printer off and call a technician. The other checks are inside the machine.

Safety: Before anyone opens the machine to work on boards or cables, switch it off and pull the plug. Part of the machine stays powered while the switch is off, so the plug must come out.

Steps for a technician

  1. 1

    Check the DDR memory (DIMM)

    Kyocera's first check for any F code: take the DIMM out of slot YS500 on the main/engine PWB, refit it and test. If the error repeats, replace the DIMM.

  2. 2

    Check the panel cable

    Check the harness and connectors between the operation panel and the main/engine PWB, then test.

  3. 3

    Run U021 (backup initialization)

    Run maintenance mode U021 to reset the controller backup data, then test the machine again.

  4. 4

    Replace the panel board

    Fit a new operation panel board and test.

  5. 5

    Replace the main/engine PWB

    If the error still shows, fit a new main/engine PWB and test again.

  6. 6

    Collect a USB log

    If nothing above clears it, save a USB log (USBLOG) from the machine and send it to Kyocera service support for study.

Need a part for this?

The store does not list the main/engine PWB or DIMM named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the F34X family error does not clear after a power reset with the plug out for a minute or more, or if it keeps coming back.

Questions people ask

What does F34X mean on a Kyocera M2040dn?
F34X means the Kyocera ECOSYS M2040dn found a fault in the panel management process, such as a command to the panel timing out.
Is F34X a broken display?
For LCD models like the M2040dn, the Kyocera manual says F34X is not caused by hardware.
How is Kyocera F34X fixed?
A technician checks the panel cable, runs U021, and then changes the panel board and the main/engine PWB if needed.

Related codes

See all Kyocera ECOSYS M2040dn error codes