Shop parts
F1DXSystem codeCritical: machine stops

Kyocera ECOSYS M2040dn error F1DX, F26X, F3AX, F47X: controller fault

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: F1DX, F26X, F27X, F28X, F29X, F2AX, F3AX, F3BX, F3CX, F3DX, F3EX, F3FX, F40X, F41X, F42X, F43X, F44X, F45X, F47X, F48X, F49X, F4DX, F4EX

Quick answer

Kyocera ECOSYS M2040dn errors F1DX, F26X to F2AX, F3AX to F45X, F47X to F49X, F4DX and F4EX are controller software faults in memory, system or image handling. All share one fix in the manual. Start with a full power reset, with the plug out for a minute or more.

What does F1DX mean?

These codes come from different parts of the controller software: image memory (F1DX), system management (F26X to F2AX), entity management (F3AX to F45X, F4DX, F4EX) and image editing (F47X to F49X). The manual gives all of them the same steps: U021, a new main/engine PWB, then a USB log. It notes F1D4 is a RAM fault cleared by U021, and that F49X is not supported on these models. The same code and checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, since Kyocera covers all of them in one service manual.

What causes F1DX?

  • Temporary controller fault

    A full power reset with the plug out may clear it.

  • Main backup data

    Stored data may need to be reset with U021. For F1D4 this is the manual's fix.

  • Main/engine PWB fault

    The main board has failed.

What can you check yourself?

  1. 1

    Full power reset

    Switch off at the power switch and pull the plug from the wall. Some power stays in the machine with the switch off, so wait a minute or more, then plug in and switch on.

  2. 2

    If the code comes back

    Write down the exact code shown, switch the printer off and call a technician. The other checks are inside the machine.

Safety: Before anyone opens the machine to work on boards or cables, switch it off and pull the plug. Part of the machine stays powered while the switch is off, so the plug must come out.

Steps for a technician

  1. 1

    Check the DDR memory (DIMM)

    Kyocera's first check for any F code: take the DIMM out of slot YS500 on the main/engine PWB, refit it and test. If the error repeats, replace the DIMM.

  2. 2

    Run U021 (backup initialization)

    Run maintenance mode U021 to reset the controller backup data, then test the machine again.

  3. 3

    Replace the main/engine PWB

    If the error still shows, fit a new main/engine PWB and test again.

  4. 4

    Collect a USB log

    If nothing above clears it, save a USB log (USBLOG) from the machine and send it to Kyocera service support for study.

Need a part for this?

The store does not list the main/engine PWB or DIMM named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the F1DX family error does not clear after a power reset with the plug out for a minute or more, or if it keeps coming back.

Questions people ask

What does F1DX mean on a Kyocera M2040dn?
F1DX covers F1D0 to F1DF and is a fault in image memory management. The manual says F1D4 is a RAM fault fixed by running U021.
Why do so many F codes share one fix?
The Kyocera manual gives these controller codes the same steps: U021, then a new main/engine PWB, then a USB log for Kyocera.
Can I clear an F code myself?
You can try a full power reset with the plug out for a minute or more. If the code comes back, a technician is needed.
What is a USB log for Kyocera F codes?
It is a record saved from the machine to a USB stick that Kyocera service support uses to study the fault.

Related codes

See all Kyocera ECOSYS M2040dn error codes