Shop parts
F46XSystem codeCritical: machine stops

Kyocera ECOSYS M2040dn error F46X: printer rendering fault

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error F46X means the machine found a fault in the part that renders print data into a page. F46F in particular can repeat with one specific print job. Start with a full power reset with the plug out for a minute, and note which document was printing.

What does F46X mean?

F46X covers F460 to F46F and comes from the printer rendering part. The manual's steps are short: replace the main/engine PWB, then get a USB log. It adds that F46F is a fault in the printer process, and if it repeats with particular print data, Kyocera wants that print data captured along with the USB log. The same code and checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, since Kyocera covers all of them in one service manual.

What causes F46X?

  • Particular print data (F46F)

    F46F can repeat when the same document is printed.

  • Main/engine PWB fault

    The board has failed.

What can you check yourself?

  1. 1

    Full power reset

    Switch off at the power switch and pull the plug from the wall. Some power stays in the machine with the switch off, so wait a minute or more, then plug in and switch on.

  2. 2

    Note the print job

    If the code appears with one document only, note which file it was and do not send it again until a technician has looked.

  3. 3

    If the code comes back

    Write down the exact code shown, switch the printer off and call a technician. The other checks are inside the machine.

Safety: Before anyone opens the machine to work on boards or cables, switch it off and pull the plug. Part of the machine stays powered while the switch is off, so the plug must come out.

Steps for a technician

  1. 1

    Check the DDR memory (DIMM)

    Kyocera's first check for any F code: take the DIMM out of slot YS500 on the main/engine PWB, refit it and test. If the error repeats, replace the DIMM.

  2. 2

    Replace the main/engine PWB

    If the error still shows, fit a new main/engine PWB and test again.

  3. 3

    Collect a USB log and print data

    Save a USB log and, where needed, capture the print data that caused the error, and send them to Kyocera service support.

Need a part for this?

The store does not list the main/engine PWB or DIMM named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the F46X family error does not clear after a power reset with the plug out for a minute or more, or if it keeps coming back.

Questions people ask

What does F46X mean on a Kyocera printer?
F46X covers F460 to F46F and means a fault in the printer rendering part, which turns print data into page images.
Why does F46F appear with one file only?
The Kyocera manual says F46F can repeat with specific print data. Kyocera asks for that data and a USB log to study it.
Does F46X always need a new board?
The manual's listed step is a new main/engine PWB, with a USB log for Kyocera. Try a full power reset first.

Related codes

See all Kyocera ECOSYS M2040dn error codes