Shop parts
J1413Paper jam codeWarning

Kyocera ECOSYS M2040dn J1413: PF feed sensor stay jam (paper feeder 2)

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn code J1413 is a PF feed sensor stay jam. Paper from the lower optional paper feeder stayed at the upper feeder's sensor for too long, so the sheet is stuck or skewed there. First clear the sheet, then fan the paper, keep it below the limit mark and set the guides.

What does J1413 mean?

With two optional paper feeders, the PF1 feed sensor should turn off within a set time after the PF2 feed sensor turns off. J1413 means paper is still sitting on the PF1 sensor. The manual checks skew and path problems first, then the PF cover, the paper and finally the sensor and boards. The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.

What causes J1413?

  • Paper caught or skewed

    Debris or burrs on the path or conveying guide, width guides not set, or paper above the limit mark.

  • Uneven roller pressure

    The front and rear PF feed roller press springs are loose or bent.

  • PF feed roller or drive gear

    Dirty or worn PF feed roller, or debris or damage on the drive gear.

  • PF cover deformed

    A bent PF cover does not close securely.

  • Paper problems

    Crushed, bent, curled, wavy or unsupported paper, or paper with foreign matter.

  • Sensor or boards

    Loose PF feed sensor (YC7) or drawer connector wiring, or a faulty PF feed sensor, PF main PWB or main/engine PWB.

What can you check yourself?

  1. 1

    Switch off before reaching inside

    Turn the power switch off before you put your hands inside a cover or the cassette slot.

  2. 2

    Clear the feeder

    Pull out the paper feeder cassettes and remove the stuck sheet and any scraps you can see.

  3. 3

    Set the paper guides

    Slide the width guides (and length guide) so they touch the stack for the size you loaded. Do not fill above the limit mark inside the tray.

  4. 4

    Close the feeder cover

    Make sure the paper feeder cover is fully closed. If it is bent and will not close, call a technician.

  5. 5

    Fan and turn the stack

    Take the paper out, fan it well and put it back the other way round, top edge to bottom. Remove any sheet with a bent or crushed edge.

  6. 6

    Use paper within specification

    Damp, wavy, curled or out-of-specification paper is a common cause. Use fresh, dry paper of a supported type and keep spare paper in a dry place.

  7. 7

    Try again

    Close all covers, switch on and print a few pages. If the same code keeps coming back, stop and call a technician.

Safety: Switch off and unplug the machine before any cover is removed for repair. The manual warns that charge can stay in the low voltage PWB capacitors for a short time after unplugging, so wait at least 5 seconds before touching boards.

Steps for a technician

  1. 1

    Clear the conveying path

    Look along the paper path for scraps of paper, foreign objects or burrs on the guides and actuators. Remove them, and replace a guide that cannot be cleaned up. Correct or replace any sheet material or film that is scratched, bent or lifting.

  2. 2

    Set guides and stack height

    Match the width guides to the paper and keep the stack within the upper limit label.

  3. 3

    Check the press springs

    Refit the PF feed roller press springs and correct or replace them if bent.

  4. 4

    Check the conveying guide

    Refit it, remove any burr, and replace it if needed.

  5. 5

    Check the PF feed roller and drive gear

    Clean or replace a worn roller, remove debris from the gear and replace it if damaged.

  6. 6

    Check the PF cover

    Make sure it closes securely and replace it if it is deformed.

  7. 7

    Check the paper

    Correct crushed, bent, curled, wavy or unsupported paper and remove sheets with foreign matter.

  8. 8

    Check wiring, sensor and boards

    Reseat PF feed sensor (PF1) to PF main PWB (YC7), the PF main PWB (YC5) to drawer connector, and drawer connector to main/engine PWB (YC17). Clean, refit or replace the PF feed sensor, then replace the PF main PWB of paper feeder 1, then the main/engine PWB.

Need a part for this?

The store does not list the paper feeder (PF) rollers, springs, cover or sensor for this code, so please ask on WhatsApp if you need one.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if J1413 keeps returning with the guides set and the feeder cover closed.

Questions people ask

What does J1413 mean on a Kyocera M2040dn?
J1413 on a Kyocera ECOSYS M2040dn means the feed sensor in the upper optional paper feeder stayed covered too long while paper came up from the lower feeder.
What is the difference between J1403 and J1413?
J1403 means the paper never reached the upper feeder's sensor. J1413 means it reached the sensor but did not leave it in time.
Can a bent paper feeder cover cause J1413?
Yes. The Kyocera manual checks whether the PF cover closes securely and replaces it if it is deformed.

Related codes

See all Kyocera ECOSYS M2040dn error codes