Kyocera ECOSYS M2040dn J4002, J4003: registration sensor non-arrival jam from cassette 2 or 3
Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw
Codes covered on this page: J4002, J4003
Quick answer
Kyocera ECOSYS M2040dn codes J4002 and J4003 mean paper fed from cassette 2 or 3, in the optional paper feeder, did not reach the registration sensor inside the printer. A sheet caught on a guide or a slipping PF conveying roller is the likely cause. First clear the sheet and reload flat paper with the guides set.
What does J4002 mean?
The registration sensor sits just before the image is transferred. J4002 (cassette 2) and J4003 (cassette 3) mean the sheet left the paper feeder but never switched that sensor on. If the sheet is damaged, look for skew, Z-folds and the PF conveying roller. If it is not damaged, the PF conveying roller is not turning or the PF conveying clutch is not working. The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.
What causes J4002?
Paper caught on the conveying guide
Foreign objects, holes or burrs on the conveying guide, or a path filled with scraps when the paper comes out Z-folded.
PF conveying roller or drive gear
The roller is dirty or worn, or the drive gear has debris or damage, causing skew or a Z-fold.
Guides, stack height or press spring
Width guides not set, paper above the limit mark, or uneven PF conveying pulley press spring pressure.
PF cover deformed
A bent PF cover delays the paper.
Paper problems
Bent, curled, wavy paper or paper with foreign matter.
Drive, clutch, sensor or boards
PF feed motor drive not reaching the roller, loose registration sensor (YC16) or PF wiring, a faulty PF conveying clutch, PF feed motor, registration sensor, PF main PWB or main/engine PWB.
What can you check yourself?
- 1
Switch off before reaching inside
Turn the power switch off before you put your hands inside a cover or the cassette slot.
- 2
Clear the sheet
Pull out cassette 2 or 3 and open the front cover as the panel shows, and remove the sheet and any scraps.
- 3
Set the paper guides
Slide the width guides (and length guide) so they touch the stack for the size you loaded. Do not fill above the limit mark inside the tray.
- 4
Fan and turn the stack
Take the paper out, fan it well and put it back the other way round, top edge to bottom. Remove any sheet with a bent or crushed edge.
- 5
Use paper within specification
Damp, wavy, curled or out-of-specification paper is a common cause. Use fresh, dry paper of a supported type and keep spare paper in a dry place.
- 6
Try again
Close all covers, switch on and print a few pages. If the same code keeps coming back, stop and call a technician.
Steps for a technician
- 1
Check the conveying guide
Remove foreign objects or burrs from its paper side or replace it. Correct or replace scratched, bent or lifting guide sheet material. For Z-folded paper, clear the path and replace a broken guide.
- 2
Check the PF conveying roller and drive gear
Clean or replace a worn roller, remove debris from the gear and replace it if damaged.
- 3
Set guides and stack height
Match the width guides to the paper and keep the stack within the upper limit label.
- 4
Check the press spring
Refit the PF conveying pulley press spring and correct or replace it if bent.
- 5
Check the PF cover
If paper is delayed, make sure the cover closes securely and replace it if deformed.
- 6
Check the paper
Remove bent sheets and sheets with foreign matter, and correct curled or wavy paper.
- 7
Check registration sensor and board
Reseat registration sensor to main/engine PWB (YC16). Clean the sensor and replace the high voltage PWB if it still fails. Replace the main/engine PWB last.
- 8
If the sheet is undamaged, check the PF drive
Turn the PF conveying roller by hand and clean, refit or replace the drive parts. Reseat the PF conveying clutch (YC2), PF feed motor (YC4), PF main PWB and drawer connectors (both feeders for J4003). Refit or replace the PF conveying clutch and the PF feed motor, check the registration sensor, then replace the PF main PWB and the main/engine PWB.
Need a part for this?
The store does not list the PF conveying roller, PF clutch or high voltage PWB for this code, so please ask on WhatsApp if you need one.
Ask on WhatsApp: +91 88899-15080When should you call a technician?
Call a technician if J4002 or J4003 keeps returning after you clear the sheet and reload good paper.
Questions people ask
- What does J4002 mean on a Kyocera M2040dn?
- J4002 on a Kyocera ECOSYS M2040dn means paper fed from cassette 2 did not reach the registration sensor in time. J4003 is the same jam for cassette 3.
- What causes Kyocera J4002 or J4003?
- The Kyocera manual checks for paper caught on the conveying guide, a slipping PF conveying roller, wrong guides, a bent PF cover, and then the PF clutch, motor, sensor and boards.
- What is the registration sensor on a Kyocera M2040dn?
- It is the sensor that sees paper just before transfer. On this model it sits on the high voltage PWB, so a faulty sensor means replacing that board.