Kyocera ECOSYS M2040dn J1403: PF feed sensor non-arrival jam (paper feeder 2)
Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw
Quick answer
Kyocera ECOSYS M2040dn code J1403 is a PF feed sensor non-arrival jam. Paper from cassette 3, the lower optional paper feeder, did not reach the sensor in the feeder above it. Skewed or bent paper and slipping PF rollers are likely causes. First clear the sheet, then fan and reload the paper with the guides set.
What does J1403 mean?
With two optional paper feeders fitted, paper from the lower one (PF2) must pass through the upper one (PF1). J1403 means the PF1 feed sensor did not turn on in time after the PF2 feed sensor did. If the sheet is undamaged, the PF1 drive or clutch is suspect; if it is damaged, the path, guides, springs and rollers are checked. The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.
What causes J1403?
PF1 drive not turning
The PF feed motor drive is not reaching the PF conveying roller of paper feeder 1.
PF1 wiring or parts
Loose PF feed sensor (YC7), PF conveying clutch (YC2), PF feed motor (YC4), PF main PWB (YC5) or drawer connector wiring, or a faulty PF feed sensor, PF conveying clutch, PF feed motor, PF main PWB or main/engine PWB.
Paper caught or skewed
Debris or burrs on the guides, width guides that do not fit, or uneven PF feed roller press spring pressure.
PF feed roller or gear
Dirty or worn PF feed roller, or debris or damage on the conveying gear.
Paper problems
Crushed, bent, curled, wavy or unsupported paper, or paper with foreign matter.
What can you check yourself?
- 1
Switch off before reaching inside
Turn the power switch off before you put your hands inside a cover or the cassette slot.
- 2
Clear the feeder
Pull out the cassettes in the paper feeder and remove the stuck sheet and any scraps you can see.
- 3
Fan and turn the stack
Take the paper out, fan it well and put it back the other way round, top edge to bottom. Remove any sheet with a bent or crushed edge.
- 4
Set the paper guides
Slide the width guides (and length guide) so they touch the stack for the size you loaded. Do not fill above the limit mark inside the tray.
- 5
Use paper within specification
Damp, wavy, curled or out-of-specification paper is a common cause. Use fresh, dry paper of a supported type and keep spare paper in a dry place.
- 6
Try again
Close all covers, switch on and print a few pages. If the same code keeps coming back, stop and call a technician.
Steps for a technician
- 1
If the sheet is undamaged, check the PF1 drive
Turn the PF conveying roller of paper feeder 1 by hand, then clean, refit or replace the drive parts.
- 2
Check PF1 wiring
Reseat PF feed sensor (YC7), PF conveying clutch (YC2) and PF feed motor (YC4) on the PF main PWB, the PF main PWB (YC5) to drawer connector, and drawer connector to main/engine PWB (YC17).
- 3
Check PF1 parts and boards
Clean, refit or replace the PF feed sensor, the PF conveying clutch and the PF feed motor of paper feeder 1. Then replace its PF main PWB, and finally the main/engine PWB.
- 4
If the sheet is damaged, clear the path
Look along the paper path for scraps of paper, foreign objects or burrs on the guides and actuators. Remove them, and replace a guide that cannot be cleaned up. Correct or replace any sheet material or film that is scratched, bent or lifting.
- 5
Set the guides
Match the width guides to the paper size if the sheet skews.
- 6
Check the press spring
Refit the PF feed roller press spring and correct or replace it if bent.
- 7
Check the PF feed roller and conveying gear
Clean or replace a worn PF feed roller, remove debris from the drive gear and replace it if damaged.
- 8
Check the paper
Correct crushed, bent, curled, wavy or unsupported paper and remove sheets with foreign matter.
Need a part for this?
The store does not list the paper feeder (PF) rollers, clutches or boards for this code, so please ask on WhatsApp if you need one.
Ask on WhatsApp: +91 88899-15080When should you call a technician?
Call a technician if J1403 returns after you clear the sheet and reload good paper, or if the paper feeders do not sit firmly together.
Questions people ask
- What does J1403 mean on a Kyocera M2040dn?
- J1403 on a Kyocera ECOSYS M2040dn means paper fed from the lower optional paper feeder did not reach the feed sensor of the paper feeder above it in time.
- Does J1403 only appear with two paper feeders?
- Yes. The manual targets paper feeder 2, so this code is for machines with two optional paper feeders stacked under the printer.
- How do I fix Kyocera J1403?
- Clear the jammed sheet, fan and reload the paper and set the guides. If it repeats, a technician checks the upper feeder's drive, clutch, motor, sensor and rollers.