Shop parts
J9300Paper jam codeWarning

Kyocera ECOSYS M2040dn J9300, J9310: DP backside timing sensor jam

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: J9300, J9310

Quick answer

Kyocera ECOSYS M2040dn codes J9300 and J9310 are jams at the document processor's backside timing sensor, used for scanning the second side. J9300 means the original did not arrive there; J9310 means it did not leave. Skewed or curled originals are a likely cause. First remove the originals, flatten them and set the width guides.

What does J9300 mean?

The DP backside timing sensor is fitted only on 40 ppm models, such as the M2040dn, M2540dn, M2540dw and M2640idw. J9300 means it did not turn on in time after the DP feed sensor turned on; J9310 means it did not turn off in time after the DP feed sensor turned off. Both share the same checks; J9300 also checks the DP feed roller. The 35 ppm models in this family do not show these codes.

What causes J9300?

  • Scraps in the document path

    A piece of paper or burr on a guide or actuator.

  • Skewed original

    A worn DP feed roller (J9300), original width guides not set, or the original catching on the DP original conveying guide.

  • Original delayed

    DP conveying roller A (and B for J9310) worn or dirty, or a deformed DP top cover that does not close.

  • Original problems

    Folded, curled, wavy or unsupported originals, or originals with foreign matter.

  • Wiring, sensor, motor or board

    Loose DP backside timing sensor (YC34) or DP feed motor (YC33) wiring, or a faulty DP backside timing sensor, DP feed motor or main/engine PWB.

What can you check yourself?

  1. 1

    Clear the document processor

    Lift the document processor cover and remove the original and any scraps of paper you can see. Close the cover firmly.

  2. 2

    Check the originals

    Remove originals with folded edges, staples, clips, tape or other matter stuck to them. Flatten curled or wavy originals, or turn them end to end and reload. Use originals within the document processor's specification.

  3. 3

    Set the original guides

    Slide the document processor's original width guides so they touch the sides of the stack.

  4. 4

    Close the top cover firmly

    Make sure the document processor top cover is fully closed. If it is bent and will not close, call a technician.

  5. 5

    Try again

    Reload the originals. If the code returns, call a technician.

Safety: Switch off and unplug the machine before anyone removes document processor covers or works on the main/engine PWB.

Steps for a technician

  1. 1

    Clear the document path

    Remove scraps of paper, foreign objects or burrs from the guides and actuators along the document path.

  2. 2

    If originals skew

    Clean or replace the DP feed roller (J9300), align the DP original width guides, and refit the DP original conveying guide, removing burrs or replacing it.

  3. 3

    If originals are delayed

    Clean DP conveying roller A (and B for J9310) and replace if worn. Make sure the DP top cover closes securely and replace it if deformed.

  4. 4

    Check the originals

    Remove folded originals and originals with foreign matter, correct or replace curled or wavy originals (switch top and bottom, or turn them over for duplex scanning), and ask users to keep to supported originals.

  5. 5

    Check wiring

    Reseat DP backside timing sensor (YC34) and DP feed motor (YC33) on the main/engine PWB.

  6. 6

    Check sensor, motor and board

    Clean, refit and reconnect the DP backside timing sensor and replace it if needed. Refit or replace the DP feed motor. Replace the main/engine PWB last.

Need a part for this?

The store does not list the DP conveying rollers or the DP backside timing sensor for this code, so please ask on WhatsApp if you need one.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if J9300 or J9310 keeps returning with flat originals and the top cover closed.

Questions people ask

What does J9300 mean on a Kyocera M2040dn?
J9300 on a Kyocera ECOSYS M2040dn means the original did not reach the document processor's backside timing sensor in time.
What does J9310 mean?
J9310 means the original reached the DP backside timing sensor but did not clear it in time. The Kyocera manual uses nearly the same checks as J9300.
Why does my Kyocera M2135dn never show J9300?
The DP backside timing sensor is only on 40 ppm models. The 35 ppm models, such as the M2135dn, do not have it.

Related codes

See all Kyocera ECOSYS M2040dn error codes