Shop parts
J9400Paper jam codeWarning

Kyocera ECOSYS M2040dn J9400, J9410: DP timing sensor jam

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: J9400, J9410

Quick answer

Kyocera ECOSYS M2040dn codes J9400 and J9410 are jams at the document processor's timing sensor, before the original is scanned. J9400 means the original did not arrive there; J9410 means it did not leave. Skewed, folded or curled originals are a likely cause. First remove the originals, flatten them and set the width guides.

What does J9400 mean?

After the DP feed sensor sees an original, the DP timing sensor should turn on and later off within a set number of motor pulses. J9400 means it did not turn on; J9410 means it did not turn off. Both share one set of checks: path, skew, delays, originals, then the sensor, DP feed motor and main/engine PWB. The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.

What causes J9400?

  • Scraps in the document path

    A piece of paper or burr on a guide or actuator.

  • Skewed original

    A worn DP feed roller, original width guides not set, or the original catching on the DP original conveying guide.

  • Original delayed

    DP conveying roller A (A and B for J9410) worn or dirty, or a deformed DP top cover.

  • Original problems

    Folded, curled, wavy or unsupported originals, or originals with foreign matter.

  • Wiring, sensor, motor or board

    Loose DP timing sensor (YC34) or DP feed motor (YC33) wiring, or a faulty DP timing sensor, DP feed motor or main/engine PWB.

What can you check yourself?

  1. 1

    Clear the document processor

    Lift the document processor cover and remove the original and any scraps of paper you can see. Close the cover firmly.

  2. 2

    Check the originals

    Remove originals with folded edges, staples, clips, tape or other matter stuck to them. Flatten curled or wavy originals, or turn them end to end and reload. Use originals within the document processor's specification.

  3. 3

    Set the original guides

    Slide the document processor's original width guides so they touch the sides of the stack.

  4. 4

    Close the top cover firmly

    Make sure the document processor top cover is fully closed. If it is bent and will not close, call a technician.

  5. 5

    Try again

    Reload the originals. If the code returns, call a technician.

Safety: Switch off and unplug the machine before anyone removes document processor covers or works on the main/engine PWB.

Steps for a technician

  1. 1

    Clear the document path

    Remove scraps of paper, foreign objects or burrs from the guides and actuators along the document path.

  2. 2

    If originals skew

    Clean or replace the DP feed roller, align the DP original width guides, and refit the DP original conveying guide, removing burrs or replacing it.

  3. 3

    If originals are delayed

    Clean DP conveying roller A (and B for J9410) and replace if worn. Make sure the DP top cover closes securely and replace it if deformed.

  4. 4

    Check the originals

    Remove folded originals and originals with foreign matter, correct or replace curled or wavy originals (switch top and bottom, or turn them over for duplex scanning), and ask users to keep to supported originals.

  5. 5

    Check wiring

    Reseat DP timing sensor (YC34) and DP feed motor (YC33) on the main/engine PWB.

  6. 6

    Check sensor, motor and board

    Clean and reconnect the DP timing sensor and replace it if needed. Refit or replace the DP feed motor. Replace the main/engine PWB last.

Need a part for this?

The store does not list the DP conveying rollers or the DP timing sensor for this code, so please ask on WhatsApp if you need one.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if J9400 or J9410 keeps returning with flat originals and the top cover closed.

Questions people ask

What does J9400 mean on a Kyocera M2040dn?
J9400 on a Kyocera ECOSYS M2040dn means the original did not reach the document processor's timing sensor in time after the DP feed sensor saw it.
What does J9410 mean?
J9410 means the original reached the DP timing sensor but did not clear it in time. The Kyocera manual gives the same checks as J9400.
Can a bent document feeder cover cause J9400?
Yes. When originals are delayed, the Kyocera manual checks that the DP top cover closes securely and replaces it if it is deformed.

Related codes

See all Kyocera ECOSYS M2040dn error codes