Shop parts
C6030Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C6030: broken thermopile

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C6030 means the signal from the thermopile, the sensor that reads the fuser belt temperature, is out of its normal range, so the printer reports a broken thermopile. The first thing to check is a scrap of paper stuck in the fuser. If none is there, call a technician.

What does C6030 mean?

The thermopile reads the surface temperature of the fuser belt and sends it to the main/engine PWB as an analogue (AD) value. C6030 appears when that value is abnormal. A piece of paper in the fuser can block the sensor, so the manual checks for paper before the wiring and the sensor. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C6030?

  • Paper left inside the fuser

    A stuck piece of paper stops the thermopile from reading the temperature properly.

  • Loose connector or damaged wire

    The lead from the thermopile to the main/engine PWB (YC2) is not making good contact.

  • Faulty thermopile

    The thermopile itself has failed.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Switch off and unplug

    Turn the power switch off and remove the plug from the wall socket before you open any cover.

  2. 2

    Look for stuck paper

    Open the covers you normally use to clear paper jams and pull out any paper you can see near the fuser. Do not touch hot metal parts and do not unscrew anything.

  3. 3

    Try once more

    Close the covers, plug in and switch on. If C6030 comes back, leave the printer off and call a technician.

Safety: The fuser runs on mains power and the fixing section can be very hot. Before anyone works on the fuser unit or the low voltage power supply board, the manual says to switch the machine off, pull the plug and wait at least 5 seconds so the capacitors on the boards can discharge. Take care not to touch the hot parts.

Steps for a technician

  1. 1

    Clear paper from the fuser

    Remove any paper left in the fuser unit.

  2. 2

    Check the connection

    Clean the contacts and refit the connector between the thermopile and the main/engine PWB (YC2). Fit a new wire if there is no continuity.

  3. 3

    Replace the thermopile

    If the code stays, fit a new thermopile.

  4. 4

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the thermopile for this model yet. Message us on WhatsApp and we will check availability for you.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if C6030 shows again after you have cleared any visible paper. The later checks need the wiring and the thermopile reached inside the machine.

Questions people ask

What does error C6030 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C6030 means broken thermopile. The signal from the sensor that reads the fuser belt temperature is out of range.
How do I clear Kyocera C6030?
Switch off, unplug and remove any paper you can see near the fuser, taking care because it can be hot. If C6030 returns, a technician checks the thermopile wiring and then the thermopile.
Can paper cause a C6030 error?
Yes. The Kyocera service manual says a piece of paper in the fuser can stop the thermopile reading correctly, so it is the first thing to check.
Do I need a new fuser unit for Kyocera C6030?
The Kyocera manual does not list the fuser unit for C6030. It replaces the thermopile, and the main/engine PWB as the last step.

Related codes

See all Kyocera ECOSYS M2040dn error codes