Shop parts
C6050Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C6050: thermopile low temperature

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C6050 means the thermopile read the fuser belt below 100°C/212°F for 3 seconds while the printer was ready or printing. The manual's first suspect is a weak power supply. Plug the printer into its own wall socket, clear any paper near the fuser, then call a technician if it returns.

What does C6050 mean?

During stand-by or printing the fuser must stay hot. C6050 appears if the thermopile, the sensor that reads the fuser belt surface, reports less than 100°C/212°F for 3 seconds in a row. The manual first looks at the mains supply, then stuck paper, the wiring and the thermopile. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C6050?

  • Low supply voltage

    The mains voltage has fallen 10% or more below the rated voltage, or several devices share one socket.

  • Paper left inside the fuser

    A stuck piece of paper stops the thermopile from reading the temperature properly.

  • Loose connector or damaged wire

    The lead from the thermopile to the main/engine PWB (YC2) is not making good contact.

  • Faulty thermopile

    The thermopile itself has failed.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Use a separate wall socket

    Plug the printer straight into a different wall socket that no other device is using.

  2. 2

    Look for stuck paper

    With the power off and the plug out, open the covers you normally use for paper jams and remove any paper near the fuser. Do not touch hot metal parts and do not unscrew anything.

  3. 3

    Try once more

    Close the covers, plug in and switch on. If C6050 comes back, leave the printer off and call a technician.

Safety: The fuser runs on mains power and the fixing section can be very hot. Before anyone works on the fuser unit or the low voltage power supply board, the manual says to switch the machine off, pull the plug and wait at least 5 seconds so the capacitors on the boards can discharge. Take care not to touch the hot parts.

Steps for a technician

  1. 1

    Check the power source

    If the supply voltage drops by 10% or more of the rated voltage, or the outlet is shared by several devices, move the power cord to a different wall outlet.

  2. 2

    Clear paper from the fuser

    Remove any paper left in the fuser unit.

  3. 3

    Check the connection

    Clean the contacts and refit the connector between the thermopile and the main/engine PWB (YC2). Fit a new wire if there is no continuity.

  4. 4

    Replace the thermopile

    If the code stays, fit a new thermopile.

  5. 5

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the thermopile for this model yet. Message us on WhatsApp and we will check availability for you.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if C6050 returns with the printer on its own wall socket and no paper in the fuser. The later checks are inside the machine.

Questions people ask

What does error C6050 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C6050 is a thermopile low temperature error. The fuser belt read below 100°C/212°F for 3 seconds while the printer was ready or printing.
Can low voltage cause Kyocera C6050?
Yes. The Kyocera service manual checks the power supply first and suggests a different wall outlet if the voltage drops 10% or more or several devices share the outlet.
How do I fix Kyocera C6050?
Move the printer to its own wall socket and clear any paper near the fuser. If it still appears, a technician checks the thermopile wiring at YC2 and then the thermopile.
Should I use a multi-plug with a Kyocera M2040dn?
For this code the manual treats a socket shared by several devices as a cause, so give the printer its own wall socket.

Related codes

See all Kyocera ECOSYS M2040dn error codes