Shop parts
C6020Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C6020: thermopile high temperature

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C6020 means the thermopile, the sensor that reads the fuser belt temperature, reported the fuser as too hot. The first thing the manual checks is the thermopile connector on the main/engine PWB. Switch off, unplug and let the printer cool, then call a technician.

What does C6020 mean?

The thermopile watches the surface temperature of the fuser belt. C6020 appears if it reads 200°C/392°F or more for 5 seconds, or for 0.5 seconds once the drive has been stopped for at least 1 second. This second check is skipped after an emergency stop, when a relay circuit takes over. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C6020?

  • Loose connector or damaged wire

    The lead from the thermopile to the main/engine PWB (YC2) is not making good contact.

  • Faulty thermopile

    The thermopile itself gives a wrong reading.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Switch off and unplug

    Turn the power switch off, pull the plug out of the wall socket and note the code for your technician.

  2. 2

    Let it cool

    Do not open the fuser area. The fixing section can be extremely hot.

  3. 3

    Call a technician

    Every check for C6020 is inside the machine.

Safety: The fuser runs on mains power and the fixing section can be very hot. Before anyone works on the fuser unit or the low voltage power supply board, the manual says to switch the machine off, pull the plug and wait at least 5 seconds so the capacitors on the boards can discharge. Take care not to touch the hot parts.

Steps for a technician

  1. 1

    Check the connection

    Clean the contacts and refit the connector between the thermopile and the main/engine PWB (YC2). Fit a new wire if there is no continuity.

  2. 2

    Replace the thermopile

    If the code stays, fit a new thermopile.

  3. 3

    Replace the main/engine PWB

    As the final step, fit a new main/engine PWB.

Need a part for this?

The store does not list the thermopile for this model yet. Message us on WhatsApp and we will check availability for you.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician as soon as C6020 appears. Every check involves the thermopile wiring, the thermopile or the main board.

Questions people ask

What does error C6020 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C6020 is a thermopile high temperature error. The sensor that reads the fuser belt reported 200°C/392°F or more for too long.
How do I fix Kyocera C6020?
Switch the printer off and unplug it. A technician then checks the thermopile connector at YC2, replaces the thermopile if needed, and replaces the main/engine PWB as the last step.
Does Kyocera C6020 mean the fuser unit is bad?
The Kyocera service manual does not replace the fuser unit for C6020. Its checks are the thermopile wiring, the thermopile and the main/engine PWB.
What is a thermopile in a Kyocera M2040dn?
It is the sensor that reads the surface temperature of the fuser belt so the main/engine PWB can control the fuser heat.

Related codes

See all Kyocera ECOSYS M2040dn error codes