Shop parts
C6600Service codeCritical: machine stops

Kyocera ECOSYS M2040dn error C6600: fuser rotation error

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn error C6600 means the main motor is running but the printer gets no signal that the fuser roller is turning. The first and most basic cause the manual lists is paper stuck in the fuser. Switch off, unplug, clear any visible paper with care, then call a technician if it returns.

What does C6600 mean?

The fuser unit has a rotation sensor that tells the main board the fuser roller is turning. C6600 appears when the motor reports it is running steadily, yet no rotation signal arrives from the fuser for 2 seconds in a row. The same code and the same checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, because Kyocera covers all of them in one service manual.

What causes C6600?

  • Paper stuck in the fuser

    Paper left inside the fuser unit stops the fuser pressure release from working as it should.

  • Loose connector or damaged wire

    The lead from the fuser unit to the main/engine PWB (YC19) is not making good contact.

  • Faulty fuser unit

    Something inside the fuser unit has failed. The rotation sensor is part of the fuser unit.

  • Main/engine PWB fault

    The main control board is faulty. The manual lists this last.

What can you check yourself?

  1. 1

    Switch off and unplug

    Turn the power switch off and remove the plug from the wall socket before opening any cover.

  2. 2

    Clear stuck paper

    Open the covers you normally use for paper jams and remove any paper you can see near the fuser. Do not touch hot metal parts and do not unscrew anything.

  3. 3

    Try once more

    Close the covers, plug in and switch on. If C6600 comes back, leave the printer off and call a technician.

Safety: The fuser runs on mains power and the fixing section can be very hot. Before anyone works on the fuser unit or the low voltage power supply board, the manual says to switch the machine off, pull the plug and wait at least 5 seconds so the capacitors on the boards can discharge. Take care not to touch the hot parts when the fuser is taken out or put back.

Steps for a technician

  1. 1

    Clear paper from the fuser

    Take out any paper remaining in the fuser unit.

  2. 2

    Check the connection

    Clean the contacts and refit the connector between the fuser unit and the main/engine PWB (YC19). If a wire has no continuity, fit a new wire.

  3. 3

    Replace the fuser unit

    If the code remains, treat the fuser unit as faulty and fit a new one.

  4. 4

    Replace the main/engine PWB

    If a new fuser unit does not clear it, fit a new main/engine PWB.

Parts for this error

Fuser unit

Only if clearing paper in step 1 and the connector check in step 2 do not clear C6600. The manual's measure at step 3 is a complete fuser unit.

Not sure which part fits? Ask on WhatsApp

When should you call a technician?

Call a technician if C6600 returns after you have removed any visible paper. The remaining checks need the fuser unit taken out or the wiring tested.

Questions people ask

What does error C6600 mean on a Kyocera M2040dn?
On a Kyocera ECOSYS M2040dn, C6600 is a fuser rotation error. The motor reports it is running, but the rotation sensor in the fuser sends no signal for 2 seconds.
How do I clear Kyocera C6600?
Switch off, unplug and remove any paper you can see near the fuser, taking care because it can be hot. If C6600 shows again after restarting, a technician checks the fuser connector and then the fuser unit.
Which part fixes Kyocera C6600?
The Kyocera service manual replaces the complete fuser unit if stuck paper and the fuser connector are not the cause. The main/engine PWB is the last item it checks.

Related codes

See all Kyocera ECOSYS M2040dn error codes