Kyocera ECOSYS M2040dn error F000: panel and main board cannot talk
Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw
Quick answer
Kyocera ECOSYS M2040dn error F000 means the operation panel cannot communicate with the main/engine PWB, so the screen cannot be used. A loose or faulty panel cable is a common cause the manual checks. First switch off, unplug, wait at least a minute and switch on again.
What does F000 mean?
The operation panel PWB and the main/engine PWB talk to each other over a cable. When that link fails, the main board cannot detect the panel and F000 is shown. On the LCD models such as the M2040dn the screen may stay on the starting logo, and F000 appears after about 60 seconds. The same code and checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, since Kyocera covers all of them in one service manual.
What causes F000?
Controller did not start properly
A temporary start-up fault that a full power reset may clear.
Loose connector or damaged wire
The cable between the operation panel PWB (YC2) and the main/engine PWB (YC507) on LCD models is not making good contact.
Expansion or DDR memory not seated
Memory fitted on the main/engine PWB is not making proper contact.
Backup RAM data is faulty
Stored controller data is corrupt and needs to be reset with U021.
Main/engine PWB fault
The main board has failed.
Operation panel PWB fault
The panel board has failed.
What can you check yourself?
- 1
Full power reset
Switch off at the power switch and pull the plug from the wall. Some power stays in the machine with the switch off, so wait a minute or more, then plug in and switch on.
- 2
Give it time
If the screen stays on the logo, wait. On LCD models the manual counts about 60 seconds before F000 shows.
- 3
If the code comes back
Write down the exact code shown, switch the printer off and call a technician. The other checks are inside the machine.
Steps for a technician
- 1
Reset the main power
Switch off, unplug, wait 5 seconds, then reconnect and switch on.
- 2
Check the panel cable
Clean the contacts and refit the connectors between the operation panel PWB and the main/engine PWB. On LCD models these are panel YC2 and main/engine YC507; on touch panel models, panel YC6 and main/engine YC507. Replace the wire if it has no continuity.
- 3
Reseat the memory
Clean the expansion memory and refit it to the main/engine PWB. Also take out and refit the DDR memory (DIMM); replace it if it can be changed and the error remains.
- 4
Run U021 (backup initialization)
Run maintenance mode U021 to reset the controller backup data, then test the machine again.
- 5
Replace the main/engine PWB
If the error still shows, fit a new main/engine PWB.
- 6
Replace the operation panel PWB
As the last parts step, fit a new operation panel PWB.
- 7
Collect a USB log
If nothing above clears it, save a USB log (USBLOG) from the machine and send it to Kyocera service support for study.
Need a part for this?
The store does not list the main/engine PWB, operation panel PWB or memory named for this code, so please ask on WhatsApp for availability.
Ask on WhatsApp: +91 88899-15080When should you call a technician?
Call a technician if F000 shows again after a full power reset with the plug out for a minute or more. The remaining checks need the covers off.
Questions people ask
- What does F000 mean on a Kyocera M2040dn?
- On a Kyocera ECOSYS M2040dn, F000 means the main/engine PWB cannot detect the operation panel because the two boards are not communicating.
- Kyocera printer stuck on logo screen then shows F000, what to do?
- Switch it off, pull the plug, wait at least a minute and switch on. If F000 comes back, a technician checks the panel cable and the memory on the main board.
- Does F000 mean the display is broken?
- Not always. The Kyocera manual checks the cable, the memory and the backup data first, then the main/engine PWB, and only then the operation panel PWB.