Shop parts
F15XSystem codeCritical: machine stops

Kyocera ECOSYS M2040dn error F15X / F38X: card reader fault

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: F15X, F38X

Quick answer

Kyocera ECOSYS M2040dn errors F15X and F38X point to a fault with an authentication device, such as an IC card reader plugged into the USB host port. The manual first checks that device's cable and connector. Start with a full power reset, keeping the plug out for a minute or more.

What does F15X mean?

F15X comes from the part that controls the authentication device and F38X from the part that manages authentication. Both relate to a device such as an IC card reader on the USB host connector, which links to the main/engine PWB at YC510. F15X has an extra first step to check that cable; after that both codes follow the same steps. The same code and checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, since Kyocera covers all of them in one service manual.

What causes F15X?

  • Card reader cable or connector

    For F15X the manual first checks the cable between the authentication device and the USB host connector, and the link to main/engine PWB YC510.

  • Main backup data

    Stored data may need to be reset with U021.

  • Main/engine PWB fault

    The main board has failed.

What can you check yourself?

  1. 1

    Full power reset

    Switch off at the power switch and pull the plug from the wall. Some power stays in the machine with the switch off, so wait a minute or more, then plug in and switch on.

  2. 2

    Check the card reader plug

    If an IC card reader is used, check its USB plug is pushed fully into the printer's USB host port.

  3. 3

    If the code comes back

    Write down the exact code shown, switch the printer off and call a technician. The other checks are inside the machine.

Safety: Before anyone opens the machine to work on boards or cables, switch it off and pull the plug. Part of the machine stays powered while the switch is off, so the plug must come out.

Steps for a technician

  1. 1

    Check the DDR memory (DIMM)

    Kyocera's first check for any F code: take the DIMM out of slot YS500 on the main/engine PWB, refit it and test. If the error repeats, replace the DIMM.

  2. 2

    Check the card reader cable (F15X)

    Check the harness and connectors from the authentication device to the USB host connector and from there to main/engine PWB YC510, then test.

  3. 3

    Run U021 (backup initialization)

    Run maintenance mode U021 to reset the controller backup data, then test the machine again.

  4. 4

    Replace the main/engine PWB

    If the error still shows, fit a new main/engine PWB and test again.

  5. 5

    Collect a USB log

    If nothing above clears it, save a USB log (USBLOG) from the machine and send it to Kyocera service support for study.

Need a part for this?

The store does not list the main/engine PWB or DIMM named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the F15X family error does not clear after a power reset with the plug out for a minute or more, or if it keeps coming back.

Questions people ask

What is error F15X on a Kyocera printer?
F15X covers F150 to F15F and means a fault in the part that controls an authentication device, such as an IC card reader.
What is Kyocera F38X?
F38X is a fault in the authentication management part. The manual fixes it with U021 and then a new main/engine PWB if needed.
Should I unplug the card reader?
The manual does not say to. Check the card reader is firmly plugged in, do a full power reset, and call a technician if the code returns.

Related codes

See all Kyocera ECOSYS M2040dn error codes