Shop parts
F12XSystem codeCritical: machine stops

Kyocera ECOSYS M2040dn error F12X / F33X: scanner control fault

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: F12X, F33X

Quick answer

Kyocera ECOSYS M2040dn errors F12X and F33X mean the machine found a fault in its scan control, which covers the scanner and the document processor. A loose cable to the main/engine PWB is the first thing the manual checks. Start with a full power reset with the plug out for a minute.

What does F12X mean?

The X stands for any last digit, so F120 to F12F and F330 to F33F belong here. F12X is reported by the scan control section and F33X by the scan management part of the software, but the manual gives both the same checks. The scanner (ISU) and the document processor (DP) each have a CIS, sensors and a motor wired to the main/engine PWB. The same code and checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, since Kyocera covers all of them in one service manual.

What causes F12X?

  • Loose cable to the scanner or DP

    On the main/engine PWB the scanner uses YC506 and YC31, and the document processor uses YC509, YC33 and YC34.

  • Controller backup data

    Stored controller data may need to be reset with U021.

  • Scan/DP board fault

    The board on the scanner or document processor side has failed.

  • Main/engine PWB fault

    The main board has failed.

What can you check yourself?

  1. 1

    Full power reset

    Switch off at the power switch and pull the plug from the wall. Some power stays in the machine with the switch off, so wait a minute or more, then plug in and switch on.

  2. 2

    If the code comes back

    Write down the exact code shown, switch the printer off and call a technician. The other checks are inside the machine.

Safety: Before anyone opens the machine to work on boards or cables, switch it off and pull the plug. Part of the machine stays powered while the switch is off, so the plug must come out.

Steps for a technician

  1. 1

    Check the DDR memory (DIMM)

    Kyocera's first check for any F code: take the DIMM out of slot YS500 on the main/engine PWB, refit it and test. If the error repeats, replace the DIMM.

  2. 2

    Check the scanner and DP cables

    Check the harness and connectors between the scanner and document processor and the main/engine PWB (YC506, YC31, YC509, YC33, YC34), then test.

  3. 3

    Run U021 (backup initialization)

    Run maintenance mode U021 to reset the controller backup data, then test the machine again.

  4. 4

    Replace the Scan/DP board

    Fit a new Scan/DP board and test.

  5. 5

    Replace the main/engine PWB

    If the error still shows, fit a new main/engine PWB and test again.

  6. 6

    Collect a USB log

    If nothing above clears it, save a USB log (USBLOG) from the machine and send it to Kyocera service support for study.

Need a part for this?

The store does not list the main/engine PWB or DIMM named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the F12X family error does not clear after a power reset with the plug out for a minute or more, or if it keeps coming back.

Questions people ask

What does F12X mean on a Kyocera M2040dn?
F12X stands for any code from F120 to F12F. On a Kyocera ECOSYS M2040dn it means a fault was found in the scanner control section.
Is Kyocera F33X the same fix as F12X?
Yes. The Kyocera manual gives F33X, the scan management error, the same checks as F12X: cables, U021, the Scan/DP board, then the main/engine PWB.
Can I still print with an F12X error?
The manual does not say. Try a full power reset first, and call a technician if the code returns.

Related codes

See all Kyocera ECOSYS M2040dn error codes