Shop parts
F25XSystem codeCritical: machine stops

Kyocera ECOSYS M2040dn error F25X, F2BX to F32X: network control fault

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: F25X, F2BX, F2CX, F2DX, F2EX, F2FX, F30X, F31X, F32X

Quick answer

Kyocera ECOSYS M2040dn errors F25X and F2BX to F32X mean the controller found a fault in the part that handles the network. The manual says F25X may be caused by the customer's own network setup. Start with a full power reset, keeping the plug out for a minute or more.

What does F25X mean?

F25X comes from network management and F2BX to F32X from network control; the manual gives them the same steps. They relate to the Ethernet connection between the printer and the outside network. For F25X the manual adds that the office network environment itself can trigger it, so Kyocera may ask for a network packet capture along with the USB log. The same code and checks apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, since Kyocera covers all of them in one service manual.

What causes F25X?

  • Office network environment

    The manual notes F25X may occur because of the customer's network.

  • Main backup data

    Stored data may need to be reset with U021.

  • Main/engine PWB fault

    The main board has failed.

What can you check yourself?

  1. 1

    Full power reset

    Switch off at the power switch and pull the plug from the wall. Some power stays in the machine with the switch off, so wait a minute or more, then plug in and switch on.

  2. 2

    Tell your IT person

    If the error started after a network change, let whoever manages your office network know, as the manual says the network can trigger it.

  3. 3

    If the code comes back

    Write down the exact code shown, switch the printer off and call a technician. The other checks are inside the machine.

Safety: Before anyone opens the machine to work on boards or cables, switch it off and pull the plug. Part of the machine stays powered while the switch is off, so the plug must come out.

Steps for a technician

  1. 1

    Check the DDR memory (DIMM)

    Kyocera's first check for any F code: take the DIMM out of slot YS500 on the main/engine PWB, refit it and test. If the error repeats, replace the DIMM.

  2. 2

    Run U021 (backup initialization)

    Run maintenance mode U021 to reset the controller backup data, then test the machine again.

  3. 3

    Replace the main/engine PWB

    If the error still shows, fit a new main/engine PWB and test again.

  4. 4

    Collect a USB log and packet capture

    Save a USB log and, as needed, a capture of network packets, and send them to Kyocera service support.

Need a part for this?

The store does not list the main/engine PWB or DIMM named for this code, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the F25X family error does not clear after a power reset with the plug out for a minute or more, or if it keeps coming back.

Questions people ask

What does F25X mean on a Kyocera printer?
F25X covers F250 to F25F and means a fault was found in network management. The manual says it may be caused by the customer's network.
Is Kyocera F2BX or F30X a network error?
Yes. F2BX to F32X come from the network control part and follow the same steps as F25X.
Will changing the network cable fix F25X?
The manual does not list a cable change. Its steps are a power reset, U021, a new main/engine PWB and a USB log with a packet capture.

Related codes

See all Kyocera ECOSYS M2040dn error codes