Shop parts
ProblemInformation

Kyocera ECOSYS M2040dn image shifted or off-centre on the page

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

An image shifted sideways or starting at the wrong place on a Kyocera ECOSYS M2040dn is usually a placement or adjustment issue. Print the Test Page from Service Setting. If prints are off too, set the paper guides to the paper size. If only copies are off, reload the original properly, then a technician adjusts the centre line.

What is happening?

Kyocera lists two kinds: the centre of the copy does not match the centre of the original, and the top margin differs from the original. On the scanner side these come from how the original is placed and from the centre line and leading edge adjustments. On the engine side they come from the paper guides, the U034 LSU settings and, for a margin that varies page to page, the feed and registration clutches. The same checks apply to all eight models in this service manual.

What causes it?

  • Original placement

    The original is not set properly on the original tray or the contact glass.

  • Scanner adjustment

    The centre line (U067 or U072), the leading edge timing (U066 or U071) or the U411 automatic adjustment is not right.

  • Scanner mechanics

    A loose contact glass, home position sensor, scanner drive belt or drive gear screw.

  • Document processor feed

    Dirty or worn DP conveying rollers A and B, a DP drive gear that needs grease, or a DP feed motor not working right.

  • Paper guides and print timing (engine)

    Paper guides not set to the paper size, U034 centre line or leading edge timing out, or a faulty feed clutch or registration clutch.

What can you check yourself?

  1. 1

    Print the test page

    Go to System Menu > Adjustment/Maintenance > Service Setting and print the Test Page (a grey halftone sheet). If the fault is on the test page, the printing engine is the cause. If the test page is clean and only copies or scans show it, the scanner is the cause.

  2. 2

    Reload the original

    Place the original square to the glass edge, or stack it neatly in the document processor.

  3. 3

    Set the paper guides

    Move the paper width guide in the cassette, the MP tray guide or the paper feeder guide to the paper size and reload.

Steps for a technician

  1. 1

    Isolate scanner or engine

    Print the Test Page from Service Setting. A fault on the test page is an engine factor; a clean test page means a scanner factor. A fault that scales with zoom copying is also a scanner factor. On the scanner side, check whether it follows the contact glass, the DP front side (main unit CIS) or the DP back side (DPCIS, 40 ppm models only).

  2. 2

    Contact glass path

    Reset the original and refit the contact glass. Adjust the centre line in U067 [Front] and the leading edge in U066 [Front], then run U411 [Table(ChartA)]. Refit the home position sensor, the scanner drive belt and tighten the scanner drive gear screw.

  3. 3

    DP front side

    Reset the originals. Adjust U072 [Front] for centre and U071 [Front Head] for the leading edge, then run U411 [DP FU(Chart B)].

  4. 4

    DP feed

    Clean DP conveying rollers A and B and their bushings, replace them if worn, grease the DP drive gears, and refit or replace the DP feed motor.

  5. 5

    DP back side (40 ppm models)

    Reload the original, adjust U072 [Back] and run U411 [DP FD(ChartB)].

  6. 6

    Engine

    Set the paper guides to the paper size. Adjust U034 [LSU Out Left] for the centre and U034 [LSU Out Top] for the leading edge. If the top margin varies, refit or replace the feed clutch and registration clutch.

Need a part for this?

The store does not list the DP conveying rollers, DP feed motor or clutches named for this fault, so please ask on WhatsApp for availability.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if the image is still off-centre after reloading the original and setting the paper guides; the rest are service mode adjustments.

Questions people ask

Why is my Kyocera M2040dn copy not centred?
First reload the original squarely. If the copy is still off-centre, a technician adjusts the scanner centre line in U067 or U072 and runs U411.
Prints from the PC are also shifted?
Then it is the engine side. Set the paper guides to the paper size; a technician can then adjust U034 [LSU Out Left] and [LSU Out Top].
Why does the top margin change from page to page?
The Kyocera service manual links a varying leading edge to the U034 timing and to the feed clutch and registration clutch.

Related codes

See all Kyocera ECOSYS M2040dn error codes