Shop parts
J0502Paper jam codeWarning

Kyocera ECOSYS M2040dn J0502, J0503: no feed from cassette 2 or 3 (paper feeder)

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Codes covered on this page: J0502, J0503

Quick answer

Kyocera ECOSYS M2040dn codes J0502 and J0503 mean paper did not feed from cassette 2 or cassette 3, the optional paper feeder drawers. The paper or worn feed rollers are the likely cause. First pull out that cassette, remove the stuck sheet, fan and reload the paper upside down and set the guides.

What does J0502 mean?

J0502 is cassette 2 and J0503 is cassette 3, both in the optional paper feeder (PF). The leading edge did not reach the PF feed sensor or the PF conveying roller in time. The manual checks the same paper, lift plate and roller points as for cassette 1, but the drive comes from the PF feed motor, PF feed clutch and PF conveying clutch, controlled by the PF main PWB. For J0503 the signal also passes through the drawer connectors of both feeders. The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.

What causes J0502?

  • Paper problems

    Crushed cut edges, bent or curled sheets, unsupported paper or foreign matter.

  • Bottom plate does not rise

    A deformed lift spring or a bent or broken cassette bottom plate.

  • PF feed drive does not start

    Loose PF feed clutch (YC2) or PF feed motor (YC4) connectors, loose drawer connectors between the feeders and the main unit, a PF feed shaft or pin not fitted, worn drive parts, or a faulty PF feed clutch, PF feed motor, PF main PWB or main/engine PWB.

  • Pickup, feed or retard roller slipping

    Dirty or worn rollers, a retard spring off, a retard holder catching, or guides not matching the paper.

  • PF conveying roller not gripping

    If the sheet stops at the PF conveying roller, its roller, pulley, spring or bushing, the PF feed motor drive or the PF conveying clutch is at fault.

  • PF feed sensor reading unstable

    The PF feed sensor (YC7), the PF main PWB or the main/engine PWB.

What can you check yourself?

  1. 1

    Switch off before reaching inside

    Turn the power switch off before you put your hands inside a cover or the cassette slot.

  2. 2

    Clear the cassette

    Pull out the cassette shown on the panel and remove any part-fed or creased sheet and any scraps you can see.

  3. 3

    Fan and turn the stack

    Take the paper out, fan it well and put it back the other way round, top edge to bottom. Remove any sheet with a bent or crushed edge.

  4. 4

    Use paper within specification

    Damp, wavy, curled or out-of-specification paper is a common cause. Use fresh, dry paper of a supported type and keep spare paper in a dry place.

  5. 5

    Set the paper guides

    Slide the width guides (and length guide) so they touch the stack for the size you loaded. Do not fill above the limit mark inside the tray.

  6. 6

    Check the feeder is seated

    Make sure the paper feeder sits squarely under the printer and the cassette slides fully home.

  7. 7

    Try again

    Close all covers, switch on and print a few pages. If the same code keeps coming back, stop and call a technician.

Safety: Switch off and unplug the machine before any cover is removed for repair. The manual warns that charge can stay in the low voltage PWB capacitors for a short time after unplugging, so wait at least 5 seconds before touching boards.

Steps for a technician

  1. 1

    Check the paper

    Correct crushed, bent, curled or unsupported paper and remove sheets with foreign matter.

  2. 2

    If the bottom plate does not rise

    Correct or replace a deformed lift spring and replace a broken bottom plate.

  3. 3

    If the plate rises but the PF drive does not start

    Clean and reseat PF feed clutch to PF main PWB (YC2), PF feed motor to PF main PWB (YC4), the PF main PWB (YC5) and drawer connectors, and drawer connector to main/engine PWB (YC17); for J0503 include the second feeder's YC5 and YC6 links. Replace a wire with no continuity. Refit the PF feed shaft and pin, check the PF feed roller turns by hand, then refit or replace the PF feed clutch, the PF feed motor, the PF main PWB and lastly the main/engine PWB.

  4. 4

    If the edge shows slip marks or is torn

    Set the width guides. Clean or replace the pickup roller and feed roller. For a folded centre, clean or replace the retard roller and refit the retard spring. Look along the paper path for scraps of paper, foreign objects or burrs on the guides and actuators. Remove them, and replace a guide that cannot be cleaned up. Correct or replace any sheet material or film that is scratched, bent or lifting.

  5. 5

    If the sheet slips after leaving the cassette

    Clean or replace the retard roller, refit or replace the retard holder and clean or replace the feed roller. Then check the PF conveying clutch wiring (YC2) and the drawer connectors, refit or replace the PF conveying clutch, and replace the PF main PWB and main/engine PWB if needed.

  6. 6

    If the sheet stops at the PF conveying roller

    Clean or replace the feed roller. Clean the PF conveying roller and pulley, refit their spring and bushing and replace them if worn. Turn the roller by hand and clean, refit or replace the drive parts. Check guides, stack height and path, the PF wiring, the PF conveying clutch, the PF feed motor, the PF main PWB and the main/engine PWB in that order.

  7. 7

    If paper reached the PF feed sensor but it did not turn on

    Reseat PF feed sensor to PF main PWB (YC7) and the drawer connectors. Refit or replace the PF feed sensor, then the PF main PWB, then the main/engine PWB.

Parts for this error

Pickup, feed and retard rollers (set of 3)

Only if step 4, 5 or 6 finds these rollers worn after cleaning. The listing is for the main unit cassette, so confirm it matches the rollers in the optional paper feeder before ordering. The store listing is a set of three rollers with base for the main cassette and does not name each roller, so your technician should compare it with the worn parts first.

Not sure which part fits? Ask on WhatsApp

When should you call a technician?

Call a technician if J0502 or J0503 keeps returning with good paper and correct guides, or if the paper feeder does not seat properly.

Questions people ask

What is the difference between J0502 and J0503 on a Kyocera M2040dn?
J0502 is a no feed from cassette 2 and J0503 is a no feed from cassette 3. Both are drawers in the optional paper feeder of the Kyocera ECOSYS M2040dn.
How do I clear Kyocera J0502?
Pull out cassette 2, remove the stuck sheet, fan and reload the paper and set the guides. If it repeats, a technician checks the rollers and the paper feeder's clutch, motor and wiring.
Can a loose paper feeder cause J0503?
The Kyocera manual checks the drawer connectors between the feeders and the main unit, so a feeder that is not seated properly is worth checking.

Related codes

See all Kyocera ECOSYS M2040dn error codes