Shop parts
J0501Paper jam codeWarning

Kyocera ECOSYS M2040dn J0501: no paper feed from cassette 1

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn code J0501 means paper did not feed from cassette 1, the main paper drawer, in time. The most common cause is the paper itself or worn, dirty feed rollers. First pull out the cassette, remove any half-fed sheet, fan the paper, reload it upside down and set the width guides.

What does J0501 mean?

During feeding from cassette 1, the next sensor in the path did not turn on in time. The manual sorts J0501 by what the technician sees on the stuck sheet: no feed marks at all, slip marks from the pickup roller, a torn or folded leading edge, or paper that stopped at the middle roller. Each points to a different part, from the cassette lift plate to the rollers, the feed clutch, the main motor or the registration sensor. The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.

What causes J0501?

  • Paper problems

    Crushed cut edges, a bent leading edge, paper curled downwards or wavy, unsupported paper or foreign matter on the sheet.

  • Cassette bottom plate does not rise

    The lift spring is deformed, or the bottom plate itself is bent or broken, so the stack never reaches the pickup roller.

  • Feed drive does not start

    A loose connector or broken wire for the feed clutch (YC10) or main motor (YC9), a feed roller shaft or pin that is not fitted, worn drive parts, or a faulty feed clutch, main motor or main/engine PWB.

  • Pickup or feed roller slipping

    Slip marks on the edge mean the pickup roller or feed roller is dirty or worn, or the width guides do not fit the paper.

  • Retard roller not working

    A folded or torn centre of the leading edge points to a dirty or worn retard roller, a retard spring that has come off, or a retard holder that is caught and adds load.

  • Middle roller not gripping

    If the sheet stops at the middle roller, its roller, pulley, spring or bushing is dirty, loose or worn, or the main motor drive is not reaching it.

  • Paper overfilled or skewed

    Paper loaded above the limit mark, or guides not set, makes the sheet skew and jam.

  • Registration sensor reading unstable

    If the paper reached the registration sensor but it did not switch on, the sensor wiring (YC16), the sensor on the high voltage PWB or the main/engine PWB is at fault.

What can you check yourself?

  1. 1

    Switch off before reaching inside

    Turn the power switch off before you put your hands inside a cover or the cassette slot.

  2. 2

    Clear the cassette

    Pull out cassette 1 and remove any sheet that is half fed or creased. Look into the slot and remove torn scraps you can see.

  3. 3

    Fan and turn the stack

    Take the paper out, fan it well and put it back the other way round, top edge to bottom. Remove any sheet with a bent or crushed edge.

  4. 4

    Use paper within specification

    Damp, wavy, curled or out-of-specification paper is a common cause. Use fresh, dry paper of a supported type and keep spare paper in a dry place.

  5. 5

    Set the paper guides

    Slide the width guides (and length guide) so they touch the stack for the size you loaded. Do not fill above the limit mark inside the tray.

  6. 6

    Check the bottom plate moves

    With the cassette out, press the metal plate in the bottom of the tray. If it is bent, stuck or broken, ask a technician.

  7. 7

    Try again

    Close all covers, switch on and print a few pages. If the same code keeps coming back, stop and call a technician.

Safety: Switch off and unplug the machine before any cover is removed for repair. The manual warns that charge can stay in the low voltage PWB capacitors for a short time after unplugging, so wait at least 5 seconds before touching boards.

Steps for a technician

  1. 1

    Check the paper

    Look for crushed cut ends, bent edges, downward curl, waves, unsupported paper or foreign matter, and correct the paper or loading first.

  2. 2

    If the bottom plate does not rise

    Correct or replace a deformed lift spring. Replace the cassette bottom plate if it is bent or broken.

  3. 3

    If the plate rises but the feed drive does not start

    Clean and reseat the feed clutch to main/engine PWB (YC10) and main motor to main/engine PWB (YC9) connectors, and replace a wire with no continuity. Refit the feed shaft and feed pin, replacing them if bent. Turn the feed roller by hand, then clean, refit or replace the drive parts. Refit or replace the feed clutch, then the main motor, then the main/engine PWB.

  4. 4

    If the edge shows slip marks

    Set the width guides to the paper. Clean the pickup roller surface and replace it if worn. Do the same for the feed roller.

  5. 5

    If a corner or side of the edge is torn

    Correct or replace downward-curled paper, then clear the conveying path as described for skewed or bent paper.

  6. 6

    If the centre of the edge is folded or torn

    Clean the retard roller and replace it if worn. Refit the retard spring if it has come off, then clear the conveying path. Look along the paper path for scraps of paper, foreign objects or burrs on the guides and actuators. Remove them, and replace a guide that cannot be cleaned up. Correct or replace any sheet material or film that is scratched, bent or lifting.

  7. 7

    If the sheet slips before the middle roller

    Clean or replace the retard roller, refit or replace the retard holder if it catches, clean or replace the feed roller, set the width guides and keep the stack under the limit label.

  8. 8

    If the sheet stops at the middle roller

    Clean or replace the feed roller. Clean the middle roller and middle pulley, refit their spring and bushing, and replace them if bent or worn. Turn the middle roller by hand and clean, refit or replace the drive parts. Then check guides, stack height and path, the main motor connector (YC9), the main motor and finally the main/engine PWB.

  9. 9

    If paper reached the registration sensor but it did not turn on

    Reseat the registration sensor to main/engine PWB (YC16) connector. Clean the registration sensor; if it still fails, replace the high voltage PWB that carries it. Replace the main/engine PWB last.

Parts for this error

Pickup, feed and retard rollers (set of 3)

Only if step 4, 6, 7 or 8 finds the pickup roller, feed roller or retard roller worn after cleaning. The store listing is a set of three rollers with base for the main cassette and does not name each roller, so your technician should compare it with the worn parts first.

Pick up unit spring

Only if step 2 finds the cassette lift spring deformed beyond correction. The store calls this a pick up unit spring and does not say which spring it is, so only use it if your technician confirms it matches the one being replaced.

Not sure which part fits? Ask on WhatsApp

When should you call a technician?

Call a technician if J0501 returns with fresh, well-loaded paper and the guides set correctly, or if the cassette bottom plate does not move freely.

Questions people ask

What does J0501 mean on a Kyocera M2040dn?
J0501 on a Kyocera ECOSYS M2040dn means paper did not feed from cassette 1 in time, so the next sensor in the path never saw it.
How do I fix Kyocera J0501?
Remove the stuck sheet, fan the paper, reload it upside down and set the width guides. If it keeps happening, a technician cleans or replaces the pickup, feed and retard rollers and checks the feed clutch and lift plate.
Do worn rollers cause J0501?
Yes. Slip marks on the paper edge point to a dirty or worn pickup or feed roller, and a folded centre points to the retard roller. The manual says to clean them first and replace them if worn.
Why does the paper not lift in cassette 1?
If the bottom plate does not rise, the Kyocera manual checks for a deformed lift spring and a bent or broken bottom plate.

Related codes

See all Kyocera ECOSYS M2040dn error codes