Shop parts
J0508Paper jam codeWarning

Kyocera ECOSYS M2040dn J0508: no paper feed from the duplex section

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn code J0508 means a sheet being printed on both sides did not return from the duplex section to the registration sensor in time. Damp, curled or unsupported paper is the usual cause. First open the covers, remove the stuck sheet, and print duplex with fresh, dry paper.

What does J0508 mean?

In duplex printing the sheet is switched back after side one and sent through the duplex (DU) path. J0508 appears when the registration sensor does not see the sheet after the exit solenoid has switched it back. The manual splits this into a damaged sheet (caught, slipping) and an undamaged sheet (the duplex drive is not turning). The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.

What causes J0508?

  • General mechanical causes

    Dirty guides and the other prior standard checks for any jam.

  • Paper caught in the duplex path

    Scraps, burrs or a lifted sheet or film on the conveying guides.

  • Curled, damp or unsupported paper

    Curled or wavy damp paper bends the leading edge; unsupported paper slips at the DU conveying roller.

  • DU conveying roller and pulley

    Dirty or worn rollers, weak pressure, a loose spring or bushing, or debris on the drive gear.

  • Registration sensor actuator

    The actuator or its spring is loose or bent.

  • Duplex drive not turning

    Main motor drive not reaching DU conveying rollers A and B, loose registration sensor (YC16) or main motor (YC9) wiring, a faulty registration sensor, main motor or main/engine PWB.

What can you check yourself?

  1. 1

    Switch off before reaching inside

    Turn the power switch off before you put your hands inside a cover or the cassette slot.

  2. 2

    Clear the duplex path

    Open the covers the panel points to and remove the sheet gently. Let the fuser area cool before reaching near it.

  3. 3

    Use paper within specification

    Damp, wavy, curled or out-of-specification paper is a common cause. Use fresh, dry paper of a supported type and keep spare paper in a dry place.

  4. 4

    Try again

    Close all covers, switch on and print a few pages. If the same code keeps coming back, stop and call a technician.

Safety: The fixing section can be very hot, so let it cool and take care not to touch hot parts when clearing paper near the fuser or removing the fuser unit. Before any work on boards, switch off, unplug and wait at least 5 seconds so the capacitors can discharge.

Steps for a technician

  1. 1

    Run the general jam checks

    Carry out the prior standard check items for any jam, such as dirty guides.

  2. 2

    Clear the conveying path

    Look along the paper path for scraps of paper, foreign objects or burrs on the guides and actuators. Remove them, and replace a guide that cannot be cleaned up. Correct or replace any sheet material or film that is scratched, bent or lifting.

  3. 3

    Check the paper

    Replace damp paper that curls or waves, and use only supported paper if the sheet slips at the DU conveying roller.

  4. 4

    Check the DU conveying roller and pulley

    Clean them, check their pressure, refit any loose spring or bushing and replace a bent or worn roller or pulley. Remove debris from the drive gear and replace it if damaged.

  5. 5

    Check the registration sensor actuator

    Refit the actuator and spring and correct or replace them if bent.

  6. 6

    If the sheet is undamaged, check the duplex drive

    Turn DU conveying rollers A and B by hand, then clean, refit or replace the drive parts.

  7. 7

    Check the wiring

    Reseat registration sensor (on the high voltage PWB) to main/engine PWB (YC16) and main motor to main/engine PWB (YC9). Replace a wire with no continuity.

  8. 8

    Check the sensor, motor and board

    Clean the registration sensor and replace the high voltage PWB if it still fails. Refit or replace the main motor. Replace the main/engine PWB last.

Need a part for this?

The store does not list the DU conveying rollers or the other duplex parts named for this code, so please ask on WhatsApp if you need one.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if J0508 keeps returning with fresh, dry paper, or if the duplex rollers do not turn.

Questions people ask

What does J0508 mean on a Kyocera M2040dn?
J0508 on a Kyocera ECOSYS M2040dn means paper did not feed back from the duplex section to the registration sensor during two-sided printing.
Why does my Kyocera jam only when printing both sides?
For duplex jams the Kyocera manual points first to damp, curled or unsupported paper, then to the DU conveying rollers, the registration sensor actuator and the duplex drive.
How is J0508 different from J4008?
J0508 is a duplex no feed, judged after the exit solenoid switches the sheet back. J4008 is a registration sensor non-arrival jam for a sheet fed from the duplex section.

Related codes

See all Kyocera ECOSYS M2040dn error codes