Shop parts
J0518Paper jam codeWarning

Kyocera ECOSYS M2040dn J0518: multi-feeding from the duplex section

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn code J0518 is a multi-feeding jam from the duplex section. During two-sided printing the registration sensor stayed covered for too long. Wavy or bent paper is a common cause. First clear the jammed sheets, then reload flat, dry paper and try the duplex job again.

What does J0518 mean?

When a sheet comes back from the duplex path, the registration sensor should turn off within a set time after the registration clutch engages. J0518 means it did not. The manual checks the paper first, then the registration clutch, registration sensor and main/engine PWB. The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.

What causes J0518?

  • Paper problems

    Crushed cut ends, bent edges, foreign matter, or paper that is wavy from moisture or curled.

  • Loose wiring

    Registration clutch (YC10) or registration sensor (YC16) connectors on the main/engine PWB.

  • Registration clutch stays engaged

    If the paper reached the registration roller but shows no loop mark, the clutch keeps the roller turning.

  • Registration sensor fault

    The sensor on the high voltage PWB is dirty or faulty.

  • Main/engine PWB fault

    Checked last.

What can you check yourself?

  1. 1

    Switch off before reaching inside

    Turn the power switch off before you put your hands inside a cover or the cassette slot.

  2. 2

    Clear the sheets

    Open the covers shown on the panel and remove all sheets in the duplex path. Let the fuser area cool first.

  3. 3

    Fan and turn the stack

    Take the paper out, fan it well and put it back the other way round, top edge to bottom. Remove any sheet with a bent or crushed edge.

  4. 4

    Use paper within specification

    Damp, wavy, curled or out-of-specification paper is a common cause. Use fresh, dry paper of a supported type and keep spare paper in a dry place.

  5. 5

    Try again

    Close all covers, switch on and print a few pages. If the same code keeps coming back, stop and call a technician.

Safety: The fixing section can be very hot, so let it cool and take care not to touch hot parts when clearing paper near the fuser or removing the fuser unit. Before any work on boards, switch off, unplug and wait at least 5 seconds so the capacitors can discharge.

Steps for a technician

  1. 1

    Check the paper

    Fan crushed sheets and reload them reversed, remove bent sheets and sheets with foreign matter, and correct or replace wavy or curled paper.

  2. 2

    Check wiring

    Reseat registration clutch to main/engine PWB (YC10) and registration sensor to main/engine PWB (YC16), and replace a wire with no continuity.

  3. 3

    Check the registration clutch

    If paper reached the registration roller but has no loop mark, refit the clutch and reconnect it, then replace it if needed.

  4. 4

    Check the registration sensor

    Clean it and reconnect. If it still fails, replace the high voltage PWB that carries it.

  5. 5

    Replace the main/engine PWB

    As the last step.

Need a part for this?

The store does not list the registration clutch or high voltage PWB for this code, so please ask on WhatsApp if you need one.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if J0518 returns with flat, dry paper.

Questions people ask

What does J0518 mean on a Kyocera M2040dn?
J0518 on a Kyocera ECOSYS M2040dn means multi-feeding from the duplex section: the registration sensor stayed on too long during two-sided printing.
What causes Kyocera J0518?
The Kyocera manual checks paper condition first, then the registration clutch, the registration sensor on the high voltage PWB and the main/engine PWB.
Is J0518 the same as J0508?
No. J0508 means the duplex sheet never reached the registration sensor. J0518 means the sensor stayed covered too long.

Related codes

See all Kyocera ECOSYS M2040dn error codes