Kyocera ECOSYS M2040dn J4008: registration sensor non-arrival jam from duplex
Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw
Quick answer
Kyocera ECOSYS M2040dn code J4008 means a sheet fed back from the duplex section did not reach the registration sensor during two-sided printing. Damp, curled or bent paper and slipping DU conveying rollers are the likely causes. First clear the sheet, then reload fresh, dry paper and try again.
What does J4008 mean?
For side two, the sheet travels through the duplex path on DU conveying rollers A and B, driven by the main motor, back to the registration sensor. J4008 means it never arrived. The manual checks the paper, then the DU rollers and pulleys, the drive and finally the sensor, motor and board. The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.
What causes J4008?
Paper problems
Crushed cut ends, bent edges, foreign matter, or paper wavy with moisture or curled.
DU conveying rollers slipping
DU conveying rollers A and B or pulleys A and B are dirty or worn, or a press spring is bent.
Duplex drive not turning
The main motor drive is not reaching DU conveying rollers A and B.
Wiring, sensor, motor or board
Loose registration sensor (YC16) or main motor (YC9) wiring, or a faulty registration sensor, main motor or main/engine PWB.
What can you check yourself?
- 1
Switch off before reaching inside
Turn the power switch off before you put your hands inside a cover or the cassette slot.
- 2
Clear the sheet
Open the covers shown on the panel and remove the sheet from the duplex path. Let the fuser area cool first.
- 3
Fan and turn the stack
Take the paper out, fan it well and put it back the other way round, top edge to bottom. Remove any sheet with a bent or crushed edge.
- 4
Use paper within specification
Damp, wavy, curled or out-of-specification paper is a common cause. Use fresh, dry paper of a supported type and keep spare paper in a dry place.
- 5
Try again
Close all covers, switch on and print a few pages. If the same code keeps coming back, stop and call a technician.
Steps for a technician
- 1
Check the paper
Fan crushed sheets and reload them reversed, remove bent sheets and sheets with foreign matter, and correct or replace wavy or curled paper.
- 2
Check the DU conveying rollers and pulleys
Clean DU conveying rollers A and B and pulleys A and B and replace them if worn. Correct and refit a bent press spring, or replace it.
- 3
Check the drive
Turn DU conveying rollers A and B by hand and clean, refit or replace the drive parts.
- 4
Check wiring
Reseat registration sensor (YC16) and main motor (YC9) on the main/engine PWB.
- 5
Check sensor, motor and board
Clean the registration sensor and replace the high voltage PWB if it still fails. Refit or replace the main motor. Replace the main/engine PWB last.
Need a part for this?
The store does not list the DU conveying rollers or pulleys for this code, so please ask on WhatsApp if you need one.
Ask on WhatsApp: +91 88899-15080When should you call a technician?
Call a technician if J4008 returns with fresh, dry paper.
Questions people ask
- What does J4008 mean on a Kyocera M2040dn?
- J4008 on a Kyocera ECOSYS M2040dn means a sheet coming back from the duplex section did not reach the registration sensor in time.
- Why does my Kyocera jam on the second side?
- For J4008 the Kyocera manual checks damp or curled paper first, then DU conveying rollers A and B, their pulleys and springs, and the main motor drive.
- Is J4008 the same as J0508?
- Both involve the duplex path. J0508 is judged after the exit solenoid switches the sheet back, while J4008 is a registration sensor non-arrival jam for a duplex sheet. The checks overlap but are listed separately.