Shop parts
J0509Paper jam codeWarning

Kyocera ECOSYS M2040dn J0509: no paper feed from the MP tray

Applies to: Kyocera ECOSYS M2040dn, Kyocera ECOSYS M2135dn, Kyocera ECOSYS M2635dn, Kyocera ECOSYS M2635dw, Kyocera ECOSYS M2735dw, Kyocera ECOSYS M2540dn, Kyocera ECOSYS M2540dw, Kyocera ECOSYS M2640idw

Quick answer

Kyocera ECOSYS M2040dn code J0509 means paper loaded in the MP tray, the bypass tray, did not reach the registration sensor. Bent, curled or unsupported paper and a dirty MP feed roller are common causes. First remove the paper, fan it, check the edges are flat and reload it with the guides set.

What does J0509 mean?

The registration sensor did not turn on while feeding from the MP tray. If the sheet is damaged, the manual looks at the paper, the path and the MP feed roller. If the sheet is not damaged, the MP bottom plate may not be lifting or the feed drive may not be starting, which points to the lift cam, the MP solenoid or the main motor drive. The same code and steps apply to the ECOSYS M2135dn, M2635dn, M2635dw, M2735dw, M2540dn, M2540dw and M2640idw, which share one Kyocera service manual.

What causes J0509?

  • Paper problems

    Bent leading edge, downward curl or waves, foreign matter, crushed cut ends or unsupported paper.

  • Paper caught in the path

    Scraps, burrs or lifted sheet material on the conveying guides.

  • MP feed roller worn or dirty

    The MP feed roller does not grip enough.

  • Registration sensor actuator

    The actuator is bent or not moving properly.

  • MP bottom plate does not lift

    The lift cam is out of position, the MP bottom plate is fitted badly, or the MP solenoid is not working.

  • Feed drive does not start

    The main motor drive is not reaching the MP feed roller, or the wiring, registration sensor, main motor or main/engine PWB is at fault.

What can you check yourself?

  1. 1

    Switch off before reaching inside

    Turn the power switch off before you put your hands inside a cover or the cassette slot.

  2. 2

    Remove and reload the MP tray paper

    Take out the paper, remove any sheet with a bent edge, fan the rest and reload a smaller stack with the guides touching the paper.

  3. 3

    Use paper within specification

    Damp, wavy, curled or out-of-specification paper is a common cause. Use fresh, dry paper of a supported type and keep spare paper in a dry place.

  4. 4

    Try again

    Close all covers, switch on and print a few pages. If the same code keeps coming back, stop and call a technician.

Safety: Switch off and unplug the machine before any cover is removed for repair. The manual warns that charge can stay in the low voltage PWB capacitors for a short time after unplugging, so wait at least 5 seconds before touching boards.

Steps for a technician

  1. 1

    Check the paper

    Remove bent sheets and sheets with foreign matter, correct curled or wavy paper, fan crushed edges and use only supported paper.

  2. 2

    Clear the conveying path

    Look along the paper path for scraps of paper, foreign objects or burrs on the guides and actuators. Remove them, and replace a guide that cannot be cleaned up. Correct or replace any sheet material or film that is scratched, bent or lifting.

  3. 3

    Check the MP feed roller

    Clean its surface and replace it if worn.

  4. 4

    Check the registration sensor actuator

    Correct and refit a bent actuator, and replace it if that does not help.

  5. 5

    If the MP bottom plate does not lift

    Align and refit the bottom plate elevation cam, refit the MP bottom plate, then refit or replace the MP solenoid and reconnect it.

  6. 6

    If the MP feed roller does not turn

    Turn it by hand and clean, refit or replace the drive parts.

  7. 7

    Check wiring, sensor, motor and board

    Reseat registration sensor (YC16) and main motor (YC9) connectors on the main/engine PWB. Clean the registration sensor and replace the high voltage PWB if needed. Refit or replace the main motor, then the main/engine PWB.

Need a part for this?

The store does not list the MP feed roller, MP solenoid or lift cam for this code, so please ask on WhatsApp if you need one.

Ask on WhatsApp: +91 88899-15080

When should you call a technician?

Call a technician if J0509 returns with flat, supported paper, or if the MP tray plate does not lift.

Questions people ask

What does J0509 mean on a Kyocera M2040dn?
J0509 on a Kyocera ECOSYS M2040dn means paper did not feed from the MP (multipurpose or bypass) tray to the registration sensor.
Why will the Kyocera bypass tray not pick up paper?
The manual lists bent, curled or unsupported paper, a dirty or worn MP feed roller, and an MP bottom plate that does not lift because of the cam or the MP solenoid.
Can I clean the MP feed roller myself?
The manual treats roller cleaning and replacement as service work, so ask a technician if reloading good paper does not help.

Related codes

See all Kyocera ECOSYS M2040dn error codes